Ryobi TR31 TOO Slow Feeding, Depth of CUT, TOO Slow TOO Fast Depth Width CUT, 1ST. Pass 2ND. Pass

OPERATION

chips, and a rougher finish. Bigger chips also require more power, which could result in the trimmer motor becoming overloaded.

Under extreme force-feeding conditions the relative speed of the cutter can become so slow — and the bites it has to take so large — that chips will be partially knocked off (rather than fully cut off), with resulting splintering and gouging of the workpiece. See Figure 6.

Your trimmer is an extremely high-speed tool (23,000 RPM no-load speed), and will make clean, smooth cuts if allowed to run freely without the overload of a forced (too fast) feed. Three things that cause “force feeding” are cutter size, depth-of-cut, and workpiece characteristics. The larger the cutter or the deeper the cut, the more slowly the trimmer should be moved forward. If the wood is very hard, knotty, gummy or damp, the operation must be slowed still more.

You can always detect “force feeding” by the sound of the motor. Its high-pitched whine will sound lower and stronger as it loses speed. Also, the strain of holding the tool will be noticeably increased.

TOO SLOW FEEDING

It is also possible to spoil a cut by moving the trimmer for- ward too slowly. When it is advanced into the work too slowly, a revolving cutter does not dig into new wood fast enough to take a bite; instead, it simply scrapes away sawdust-like particles. Scraping produces heat, which can glaze, burn, or mar the cut — in extreme cases, it can even overheat the cutter so as to destroy its hardness. Dull cutters can also contribute to scraping and burning.

In addition, it is more difficult to control a trimmer when the cutter is scraping instead of cutting. With practically no load on the motor the cutter will be revolving at close to top RPM, and will have a much greater than normal tendency to bounce off the sides of the cut (especially, if the wood has a pronounced grain with hard and soft areas). As a result, the cut produced may have sides that are rippled instead of straight.

“Too-slow feeding” can also cause your trimmer to take off in a wrong direction from the intended line of cut. You can detect “too-slow feeding” by the high-pitched sound of the motor. Always grasp and hold your trimmer firmly when trimming.

DEPTH OF CUT

See Figure 7.

As previously mentioned, the depth of cut is important because it affects the rate of feed which, in turn, affects the quality of a cut (and, also, the possibility of damage to your trimmer motor and cutter). A deep cut requires a slower feed than a shallow one, and a too deep cut will cause you to slow the feed so much that the cutter is no longer cutting, it is scraping, instead.

Making a deep cut is never advisable. The smaller cutters— especially those only 1/16 in. (1.6 mm) in diameter — are easily broken off when subjected to too much side thrust. A

TOO SLOW

TOO FAST Fig. 6

	DEPTH		WIDTH
	OF CUT
			OF CUT
2ND.	1ST.	1ST. PASS
	PASS	2ND. PASS
PASS

Fig. 7

large enough cutter may not be broken off, but if the cut is too deep a rough cut will result — and it may be very difficult to guide and control the cutter as desired. For these reasons, we recommend that you do not exceed 1/8 in. (3.2 mm) depth of cut in a single pass, regardless of the cutter size or the softness or condition of the workpiece. This will result in a higher quality cut.

To make deeper cuts it is therefore necessary to make as many successive passes as required, lowering the cutter 1/8 in. (3.2 mm) for each new pass. In order to save time, do all the cutting necessary at one depth setting, before lowering the cutter for the next pass. This will also assure a uniform depth when the final pass is completed.

WARNING:

If desired depth of cut is greater than can be safely cut in one pass, make cuts in two or more passes.

Page 10