Graco 312394V important safety instructions Electric Shock Hazard

Page 10

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

Turn off and disconnect power cord before servicing equipment.

Use only grounded electrical outlets.

Use only 3-wire extension cords.

Ensure ground prongs are intact on power and extension cords.

Do not expose to rain. Store indoors.

SKIN INJECTION HAZARD

High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point dispense valve at anyone or at any part of the body.

Do not put your hand over the end of the dispense nozzle.

Do not stop or deflect leaks with your hand, body, glove, or rag.

Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

Read MSDS’s to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

Always wear impervious gloves when spraying or cleaning equipment.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

Protective eyewear

Clothing and respirator as recommended by the fluid and solvent manufacturer

Gloves

Hearing protection

10

312394V

Image 10
Contents PR70 and PR70v Feed Systems Contents Related ManualsProduct Configurator PR7FLow Volume Side Piston High Pressure, 3/8 in .5 mm 2.5 ft Code K Part Dispense Valve Code M Part Applicator Mounting Code Q Part High Volume Side Tank Cover Code Part Off-Board Tank Stands Electric Shock Hazard Fire and Explosion Hazard Grounding Installation Polyethylene Tank Lid with AgitatorLevel Sensors Pneumatic Agitator MotorPolyethylene Tanks Stainless Steel Tanks AccumulatorsAuto-Refill Installation Pressure Transducer and Flow Meter InstallationAdvanced Display Module Disabled Mode StartupPressure Relief Procedure Level Sensor Calibration SetupRelieve pressure. See Pressure Relief Procedure, Stainless Steel Tanks Polyethylene TanksVacuum De-gas Vacuum De-gas and Vacuum Auto-Fill Accumulator Filling Relieve pressure. See Pressure Relief Procedure on ShutdownTank Removal RepairBall Valve Removal from Tank Assembly 255284 Shown Ball Valve RepairAgitator Fuse Replacement Parts Accumulators, Assemblies LC0160 and LC0297Accumulators Part Description Qty RingAssembly 255282 Shown 224 211 Liter Polyethylene Tanks† ‹ Polyethylene Tank Agitators Electric Agitator Assemblies 255246† Part not shown Pneumatic Agitator Assembly 801 802 808 813 823 805 824 804 807 806 814 822Part Description Agitator Shaft On-Board Stainless Steel Tanks Tank Assemblies LC0237, LC0238 LC0254, and LC0255Part Description Qty Part Description Qty DescriptionQtyBall Valve, Assembly Flange Assembly On-Board Stainless Steel Tank Lids Lid Assemblies LC0019 to LC0026 and LC0130 to LC0132LC0023, Lid assembly Agitator, De-gas LC0012 LC0235 LC0013 Tanks for Use with Dust CoversTanks for Use with Clampdown Covers 24U714 24U713 24U715Lid Assembly LC0018 Off-Board Stainless Steel Tanks Tank Assemblies LC0054 and LC0055Assembly LC0259 Shown Tank Assemblies LC0259 and LC0260Pipe and Tube System Lid Assembly LC0101 Off-Board Stainless Steel Tank LidsLid Assembly LC0102 Parts 312394V Assembly LC0147 Shown Lid Assemblies LC0050, LC0144, LC0145, LC0146, LC0147Agitator Vacuum De-gas Quantity LC0050 LC0145 LC0146 LC0147 60 L LC0144 PneumaticAgitator Part Description De-gas 60 L Port, 30 L Port, 60 LLid Assemblies LC0042, LC0043, LC0142, and LC0143 Quantity LC0142 LC0143 Lid LC0043 Assembly LC0042 WithAssembly LC0051 Shown Lid Assemblies LC0047, LC0048, LC0051, LC0052Fill Vacuum Tree Manifold NPTParts 312394V Electric Agitator Motor Assembly Stainless Steel Tank AgitatorsWasher Electric Agitator Motor, Assemblies 255337 Pneumatic Agitator Motor Assembly, 02/1116/50 Pneumatic Agitator Motor Pneumatic Agitator Motor, 24J183Agitator Blade Assemblies 257607 Polyethylene Tanks Level Sensors Assembly LC0278 Stainless Steel Tanks Level Sensors 2103 2102 2101 2104Mixer and Shroud Options Tank AccessoriesKits MD2 Valve KitsRefill Kits Vacuum KitsExternal Control Interface Connection Kit PR70 DimensionsMachine with On-Board Tanks PR70v† Assembly Dimensions, in. mm Tank Machine with Off-Board TanksPage Technical Data Graco Standard Warranty Graco Information