Hobart Welding Products 3545-20, 3035-20 manual Connecting Spool Gun To Welding Power Source

Page 17

3-5. Connecting Spool Gun To Welding Power Source

5

3

2

4

5

 

7 6

1 6

Tools Needed:

8

3/4 in.

Ref. 802 582-A

! Turn off and disconnect input power.

Disconnect and remove MIG (GMAW) welding gun, if applicable.

1Front Panel Opening

2Spool Gun Weld Cable

Route weld cable through front panel open- ing.

3 Positive (+) Output Terminal

Connect spool gun weld cable to positive

(+) output terminal.

4 Work Clamp Lead

Work clamp lead should be connected to negative (−) output terminal.

5Existing Gas Hose

6Spool Gun Gas Hose

7Gas Diverter Valve

To install diverter valve, cut existing gas hose above barbed fitting at wire drive housing.

Install supplied hose clamp onto end of hose at wire drive housing, and insert either of the two output barbed ends of diverter valve into hose. Secure with hose clamp.

Install another supplied hose clamp onto end of hose from gas supply, and insert in- put barbed end of diverter valve into hose. Secure with hose clamp.

Slide hose clamp down gas hose from gun, and cut barbed fitting off hose. Route gas hose through front panel opening, and insert remaining output barbed end of diverter valve into hose. Secure with hose clamp.

8 Trigger Control Plug

Insert plug into receptacle, and tighten threaded collar.

Close welding power source door.

OM-226 857 Page 13

Image 17
Contents OM-226 857B File Wire FeederProcesses DescriptionProtect Your Investment From Hobart to YouTable of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can burnARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can injureFalling Equipment can injure Moving Parts can injureCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un incendie ou une explosion LES Pièces Chaudes peuvent provoquer des brûluresLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLes Pièces Mobiles peuvent causer des blessures Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures LE Soudage À L’ARC risque de provoquer des interférencesEn ce qui concerne les implants médicaux Principales normes de sécuritéInformations relatives aux CEM OM-226 857 Approximate Cooling Maximum Spool Weld Circuit Overall Specifications For Spool GunComponents Supplied With Spool Gun Conversion Kit Operation Turn off and disconnect in- put powerTurn off and disconnect input power Connecting Spool Gun To Welding Power SourceScrew rotation clockwise decreases Installing Wire Spool And Threading Welding WireRemoving Existing Barrel And Installing Contact Adapter Controls Routine MaintenanceChanging Lower Drive Roll Changing Drive RollsChanging Push Roll Changing Liner TroubleshootingWelding Techniques Gmaw MIG Aluminum Welding HintsBefore You Start Welding Contact Tube Position And Tip-To-Work Distance Common Problems/Troubleshooting− Electrical Diagrams − Parts List Optional Hardware is common and not available unless listed Push Roll .047 1.2 mm Page Assistance ServiceSupport Hobart Welding Products Contact your Distributor for
Related manuals
Manual 2 pages 25.69 Kb