Hobart Welding Products OM-925 217 694A manual Troubleshooting − Waviness Of Bead

Page 42

8-14. Troubleshooting − Waviness Of Bead

Waviness Of Bead − weld metal that is not parallel and does not cover joint formed by base metal.

S-0641

Possible Causes

Corrective Actions

Welding wire extends too far out of nozzle.

Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.

Unsteady hand.

Support hand on solid surface or use two hands.

8-15. Troubleshooting − Distortion

Distortion − contraction of weld metal during welding that forces base metal to move.

Base metal moves in the direction of

the weld bead.

S-0642

Possible Causes

Corrective Actions

Excessive heat input.

Use restraint (clamp) to hold base metal in position.

Make tack welds along joint before starting welding operation.

Select lower voltage range and/or reduce wire feed speed.

Increase travel speed.

Weld in small segments and allow cooling between welds.

OM-925 Page 38

Return To Table Of Contents

Image 42

Contents OM-925 ProcessesDescription From Hobart to You Table of Contents Options and Accessories Warranty Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers Identifie un message de sécurité particulier − Consignes DE Sécurité − À Lire Avant UtilisationLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LE Bruit peut affecter l’ouïe’EMPLOI Excessif peut Faire Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser LES Pièces Mobiles peuvent cau- ser des blessuresPrincipales normes de sécurité Information sur les champs électromagnétiquesConsignes relatives aux stimulateurs cardiaques − Specifications SpecificationsVAC Model Output Duty Cycle % Duty Cycle And OverheatingAmperes VAC Model Output AmperesVolt-Ampere Curves Voltage− Installation Installing Welding Gun Installing Work ClampProcess/Polarity Table Changing PolarityInstalling Gas Supply Is required Do not move or operate unit where it could tip = GND/PEElectrical Service Guide For 230 VAC Model Installing Wire Spool And Adjusting Hub TensionThreading Welding Wire Hold wire tightly to keep it From unraveling− Operation ControlsWeld Parameter Chart For 115 VAC Model Steel20 ga 18 ga 16 ga 11 ga InchWeld Parameter Chart For 230 VAC Model Wire Welding Package 18 ga 16 ga 11 ga 048 060 InchDisconnect power before maintaining − Maintenance &TROUBLESHOOTINGRoutine Maintenance Overload Protection Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide Turn Off power before replacing contact tipReplacing Gun Contact Tip Cleaning Or Replacing Gun Liner Disconnect gun from unitTo Reassemble Gun Replacing Switch And/Or Head Tube Troubleshooting Table Trouble Remedy− Electrical Diagram Circuit Diagram For 115 VAC ModelCircuit Diagram For 230 VAC Model − MIG Welding Gmaw Guidelines Typical MIG Process ConnectionsThickness to Amperage a Typical MIG Process Control SettingsWire Size Amperage Range Select VoltageHolding And Positioning Welding Gun Conditions That Affect Weld Bead Shape Poor Weld Bead Characteristics Good Weld Bead CharacteristicsGun Movement During Welding Troubleshooting − Excessive Penetration Troubleshooting − Excessive SpatterTroubleshooting − Porosity Possible Causes Corrective ActionsTroubleshooting − Lack Of Penetration Troubleshooting − Incomplete FusionTroubleshooting − Burn-Through Troubleshooting − Waviness Of Bead Troubleshooting − DistortionTroubleshooting Guide For Semiautomatic Welding Equipment Common MIG Shielding GasesApplication Welding arc not stable Wire slipping in drive rolls Return To Table Of Contents − Parts List Main AssemblyDia Part H-10 Gun Optional Drive Rolls Options195 Page Service SupportContact your Distributor for Hobart Welding Products