Hobart Welding Products S-64, S-62 Pin Plug Information, Motor Start Control, Pin Information

Page 18

4-5. 14-Pin Plug Information

 

 

 

Pin*

Pin Information

 

 

 

A

24 volts ac with respect to socket G.

 

 

 

B

Contact closure to A completes 24 volts ac contactor control circuit.

J

K

A

G

Circuit common for 24 volts AC circuit.

 

 

I

B

C

+10 volts dc output to remote control with respect to socket D.

 

 

 

 

L C

H

N

D

Remote control circuit common.

G

M

D

 

 

F

E

 

E

0 to +10 volts dc input command signal from remote control with respect to socket D.

 

 

 

H

Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts.

 

 

 

F

Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.

*The remaining pins are not used.

4-6. Wire Type, Size, And Feed Speed Capability Table

Motor Speed

Wire Type

Wire Size

Feed Speed Capability

 

 

 

 

Standard

All

.023 To 5/64 in (0.6 To 2 mm)

50 To 780 ipm (1.3 To 19.8 mpm)

 

 

 

 

Standard

All

3/32 To 7/64 in (2.4 To 2.8 mm)

50 To 700 ipm (1.3 To 17.8 mpm)

 

 

 

 

 

Standard

All

1/8 in (3.2 mm)

50 To 300 ipm (1.3

To 7.6 mpm)

 

 

 

 

 

Optional High

All

.023 To 5/64 in (0.6 To 2 mm)

92 To 1440 ipm (2.3

To 35.6 mpm)

Speed

 

 

 

 

 

 

 

 

 

4-7. Motor Start Control

2

To change wire feed starting speed proceed as follows:

Turn Off unit and welding power source.

Remove wrapper.

1 Front Panel

Remove screw from upper left cor- ner, and open hinged front panel.

1

2 Motor Board PC1

 

3 Motor Start Control

Potentiometer R70

Rotate potentiometer clockwise to increase time it takes the motor to ramp up to speed. Remove protec- tive white rubber cap before making adjustment. Adjust potentiometer R70 using a small nonconductive screwdriver.

 

Close and secure front panel, and

3

reinstall wrapper.

 

Tools Needed:

Non-Conductive

1/4 in

802 479 / Ref. 146 862-D

OM-1579 Page 14

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OM-1579 ProcessesDescription From Hobart to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersUN Choc É Lectrique peut tuer Signification des symbolesConsignes DE Securite Lire Avant Utilisation LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe ’EMPLOI Excessif peut Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques + + + DefinitionsSymbols And Definitions Rating Label For CE ProductsIntroduction InstallationSpecifications Site SelectionEquipment Connection Diagrams Gun Recommendation TableProcess Gun Rear Panel Connections And Rotating Drive Assembly Pin Plug Information Wire Type, Size, And Feed Speed Capability TableMotor Speed Wire Type Wire Size Feed Speed Capability Motor Start ControlInstalling And Threading Welding Wire To adjust drive roll pressure, hold nozzleOptional Equipment DIP Switch Settings Spot Time Range SelectionOption Interface Standard SettingsVoltage Sensing Function Operation Front Panel ControlsDisconnect power before maintaining Maintenance and TroubleshootingRoutine Maintenance Overload Protection And Optional Side Panel ControlsTroubleshooting Disconnect power before troubleshootingElectrical Diagram Circuit Diagram196 Parts List Main AssemblyOptional Control Box Control Box -1 Item Control Panel Control Panel -2 Item Drive Assembly, Wire Drive Assembly, Wire -1 Item Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive Service SupportContact your Distributor for Hobart Welding Products

S-62, S-64 specifications

Hobart Welding Products has long been recognized for its commitment to quality and innovation in the welding industry. Among their extensive range of products, the Hobart S-64 and S-62 welding machines stand out for both professional and hobbyist welders seeking high performance and reliability.

The Hobart S-64 is noted for its exceptional handling of various welding tasks. This model is built for versatility with synergistic control, which simplifies the welding process. Users can intuitively adjust parameters for different materials and thicknesses, ensuring optimal penetration and bead appearance. The S-64 supports both MIG and spool gun welding, making it suitable for a wide range of applications, from automotive repairs to fabrication projects. The inclusion of a built-in digital display allows operators to monitor settings in real-time, enhancing accuracy.

On the other hand, the Hobart S-62 is engineered for portability without sacrificing power. Weighing in at a manageable size, this unit is ideal for those who need to transport their equipment to various job sites. The S-62 boasts an advanced drive system designed to accommodate different wire diameters, providing consistent feeding and reducing the likelihood of jams. Its robust construction ensures it can endure the rigors of demanding environments, making it a reliable choice for contractors and welders on the go.

Both models incorporate innovative technology such as improved thermal protection to prevent overheating, ensuring durability during prolonged use. Additionally, the intuitive interface makes these machines accessible for beginners, while still providing the capabilities that experienced welders demand.

One of the key characteristics shared by both the S-64 and S-62 is their energy efficiency. These machines are designed to operate on standard household power, allowing users to work from virtually anywhere without the need for specialized electrical setups. This feature enhances their usability and appeals to a broad audience, from DIY enthusiasts to seasoned professionals.

Overall, the Hobart S-64 and S-62 welding machines exemplify the brand's dedication to performance, quality, and user-friendly design. With distinctive features and advanced technologies, these models set a high standard in the welding equipment market, ensuring that users can achieve precise and effective results in their projects. Whether for light fabrications or heavy-duty welding tasks, Hobart Welding Products continues to lead the way with these exceptional machines.
Top Page Image Contents