Hobart Welding Products S-62, S-64 manual Operation, Front Panel Controls

Page 21

SECTION 5 – OPERATION

5-1. Front Panel Controls

1Voltmeter (Optional) (See Section

NO TAG)

2Wire Speed Meter (Optional)

Factory set to display inches per minute. If display of meters per minute is desired, see Section 4-9.

3 Schedule A Wire Speed Control

The scale is calibrated in inches per minute x 100 and meter per minute.

4Schedule A Voltage Control (Optional)

.For dual schedule applications, a dual schedule switch is required for the gun.

Obtain a proper dual schedule switch and install according to its instructions.

5Schedule B Indicator Light (Optional)

6Schedule B Voltage Control (Optional)

7Schedule B Wire Speed Control (Op- tional)

8Press To Set Button (Optional)

Press and hold button to preset Schedule B wire feed speed and/or voltage.

9 Jog/Purge Switch

Push up to momentarily feed welding wire at speed set on Wire Speed control without en-

ergizing welding circuit or shielding gas valve.

Push down to momentarily energize gas valve to purge air from gun or adjust gas reg- ulator.

Center position is off.

10 Trigger Hold Switch (Optional)

Push up to weld without holding gun trigger throughout the weld cycle.

To start weld, press and release gun trigger within three seconds after an arc has been struck. To end weld, press and release gun trigger.

1

2

10

3

4

5

6

7

98

ST-151 845-B

OM-1579 Page 17

Page 20 Page 22
Image 21
Page 20 Page 22
Contents OM-1579 ProcessesDescription From Hobart to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killPrincipal Safety Standards About Pacemakers EMF InformationConsignes DE Securite Lire Avant Utilisation Signification des symbolesUN Choc É Lectrique peut tuer LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe LA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU’EMPLOI Excessif peut DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques Definitions + + +Rating Label For CE Products Symbols And DefinitionsSpecifications InstallationIntroduction Site SelectionEquipment Connection Diagrams Gun Recommendation TableProcess Gun Rear Panel Connections And Rotating Drive Assembly Motor Speed Wire Type Wire Size Feed Speed Capability Wire Type, Size, And Feed Speed Capability TablePin Plug Information Motor Start ControlTo adjust drive roll pressure, hold nozzle Installing And Threading Welding WireOptional Equipment DIP Switch Settings Spot Time Range SelectionOption Interface Standard SettingsVoltage Sensing Function Front Panel Controls OperationRoutine Maintenance Maintenance and TroubleshootingDisconnect power before maintaining Overload Protection And Optional Side Panel ControlsDisconnect power before troubleshooting TroubleshootingCircuit Diagram Electrical Diagram196 Main Assembly Parts ListOptional Control Box Control Box -1 Item Control Panel Control Panel -2 Item Drive Assembly, Wire Drive Assembly, Wire -1 Item Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive Support ServiceHobart Welding Products Contact your Distributor for

S-62, S-64 specifications

Hobart Welding Products has long been recognized for its commitment to quality and innovation in the welding industry. Among their extensive range of products, the Hobart S-64 and S-62 welding machines stand out for both professional and hobbyist welders seeking high performance and reliability.

The Hobart S-64 is noted for its exceptional handling of various welding tasks. This model is built for versatility with synergistic control, which simplifies the welding process. Users can intuitively adjust parameters for different materials and thicknesses, ensuring optimal penetration and bead appearance. The S-64 supports both MIG and spool gun welding, making it suitable for a wide range of applications, from automotive repairs to fabrication projects. The inclusion of a built-in digital display allows operators to monitor settings in real-time, enhancing accuracy.

On the other hand, the Hobart S-62 is engineered for portability without sacrificing power. Weighing in at a manageable size, this unit is ideal for those who need to transport their equipment to various job sites. The S-62 boasts an advanced drive system designed to accommodate different wire diameters, providing consistent feeding and reducing the likelihood of jams. Its robust construction ensures it can endure the rigors of demanding environments, making it a reliable choice for contractors and welders on the go.

Both models incorporate innovative technology such as improved thermal protection to prevent overheating, ensuring durability during prolonged use. Additionally, the intuitive interface makes these machines accessible for beginners, while still providing the capabilities that experienced welders demand.

One of the key characteristics shared by both the S-64 and S-62 is their energy efficiency. These machines are designed to operate on standard household power, allowing users to work from virtually anywhere without the need for specialized electrical setups. This feature enhances their usability and appeals to a broad audience, from DIY enthusiasts to seasoned professionals.

Overall, the Hobart S-64 and S-62 welding machines exemplify the brand's dedication to performance, quality, and user-friendly design. With distinctive features and advanced technologies, these models set a high standard in the welding equipment market, ensuring that users can achieve precise and effective results in their projects. Whether for light fabrications or heavy-duty welding tasks, Hobart Welding Products continues to lead the way with these exceptional machines.
Top Page Image Contents