Chicago Electric MIG 170 Extension Cords, Replacement Cords, Setup Basic Welding, Grounding

Page 6

SAFETY

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH

FROM INCORRECT GROUNDING WIRE CONNECTION:

Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Have a plug installed by a certified electrician.

Do not use the welder if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician,

do not use adapter plugs.

SETUP

BASIC WELDING

1.The green wire inside the cord is connected to the grounding system in the welder. The green wire in the cord must be the only wire connected to the welder’s grounding system and must never be attached to an electrically “live” terminal. Never leave the grounding wire disconnected

or modify the Power Cord Plug in any way.

2.Make sure the tool is connected to an outlet having the same configuration as the plug. If the tool must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the tool should comply with all local codes and ordinances.

3.A 250 V~ plug will need to be installed by a certified electrician before use.

4.The plug shown (NEMA 6-50p) is for use on a

50 A circuit. A different 250 V~ plug and outlet combination may be used, provided it is rated to handle the electrical requirements of the tool and is installed by a certified electrician.

DO NOT USE 125 V~ PLUG.

NOTE SIZE DIFFERENCE.

250 V~ 3-Prong Plug (6-50p) and Outlet (6-50r)

(for up to 250 V~ and up to 50 A)

WELDING TIPS

MAINTENANCE

Extension Cords

Do not use an extension cord on this welder.

Replacement Cords

1. A qualified electrician can install either of the

2.

Do not install a thinner or longer

following UL-listed, 3 wire cords as a replacement

 

cord on this welder.

cord for this welder:

3.

Do not patch cords of any length together for this

12 AWG up to

6 feet long,

10 AWG up to

75 feet long, or

 

item, patches may allow moisture to penetrate

6 AWG up to 175 feet long.

 

the insulation, resulting in electric shock.

Page 6

For technical questions, please call 1-800-444-3353.

SKU 68885

Image 6
Contents Email our technical support at tech@harborfreight.com Save this ManualTable of Contents General SafetySafety Fume and Gas SafetyArc Ray Safety Setup Basic Welding Welding Tips MaintenanceSafety Setup Electrical SafetyFire Safety Welding Welding Tips MaintenanceWelding Maintenance MaintenanceGas Shielded Welding Cylinder safety Welder use and careExtension Cords Replacement CordsSetup Basic Welding GroundingBasic Welding Welding Tips Maintenance SymbologySpecifications Setup Face Shield AssemblyTips Maintenance Plug AttachmentWire Spool Installation Setup Basic DcenDcep 8mm = .030 & 0.6mm = Tensioner ArmFeed Roller Instructions Feed Roller Knob 030/.035 groove and stamp Groove and stampSafety Hold Wire welding SecurelySetup Basic Welding Welding Tips Welding WireIncrementally Increase tension Until wire bends Turn the Welder OFFSafety Setup Basic Welding Welding Tips Maintenance Basic WeldingTo Prevent Serious Injury Dial WireControl Panel Layout CordDuty Cycle Duration of Use Torch Concrete slabMIN MAX Flux Weld SettingsMIG Weld Settings MINSetting Up The Weld Do not Switch the CurrentWhile Welding From Asphyxiation Hold Torch ClearBasic Welding Technique Stringer beadMIG only Close shielding gas tank valve completelyUp to 2 minutes Welding at rated output Cleaning the Weld Strike TestWelding Tips Weld Diagnosis Example Weld DiagramsWorkpiece Heat Control / Weld Penetration To CorrectBend at Joint Weld ProblemsPenetration Workpiece Heat Control Coat of Slag Over WeldCrooked/Wavy Bead PorosityExcessive Spatter Burn-ThroughFire and Burns Nozzle and Contact Tip Inspection and CleaningMaintenance Compressed air, blow out all dust from the interiorTroubleshooting Wire feed motor runs but wire does not feed properlyWire creates a bird’s nest during operation Welding arc not stableWire Feeds, but arc does not ignite TroubleshootingPower switch does not light when switched on Safety Setup Basic Welding Welding TipsParts List and Diagrams Wiring DiagramParts List Record Serial Number HereAssembly Diagram Welding3 4 5 6 7 8 9 10 11 12 13 Limited 90 Day Warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800

MIG 170 specifications

The Chicago Electric MIG 170 is a versatile and powerful welding machine designed for both amateur and professional welders. This compact welder is particularly suited for those who frequently work on metal fabrication projects, automotive repairs, and home improvement tasks. With its impressive performance capabilities and a range of user-friendly features, the Chicago Electric MIG 170 has become a popular choice among welding enthusiasts.

One of the standout features of the Chicago Electric MIG 170 is its robust welding output. It operates on standard 220-volt power, allowing it to deliver a consistent output that ranges from 30 to 170 amps. This wide range provides users with the capability to weld various materials, including mild steel, stainless steel, and aluminum. Additionally, it is capable of welding materials up to 5/16 inches thick, making it a reliable choice for heavy-duty applications.

The MIG 170 utilizes a gasless flux-cored wire welding process, which makes it suitable for outdoor use without the necessity of shielding gas. This feature eliminates the need for additional gas tanks, making the welding experience simpler and more cost-effective. Users can also switch to MIG welding with a gas setup if desired, allowing for greater versatility in their projects.

Moreover, this welder is equipped with an adjustable wire feed speed control, permitting users to customize their welding settings for different thicknesses of material. The easy-to-read control panel enhances usability, giving welders the ability to quickly adapt to changing conditions and requirements. A built-in thermal overload protection system further ensures that the machine operates safely, preventing damage due to overheating during extended use.

The portability of the Chicago Electric MIG 170 is another key advantage. Weighing in at approximately 60 pounds, it can easily be transported to job sites or moved around a workshop. Its compact design does not compromise on performance, making it a great addition to any workspace.

Overall, the Chicago Electric MIG 170 is an excellent welding machine that blends power, efficiency, and ease of use. Its combination of features makes it suitable for beginners and seasoned welders alike, solidifying its reputation as a go-to option in the welding community. Whether for hobbyist projects or more serious applications, the MIG 170 remains a reliable and effective choice for various welding needs.