Woodstock W1809, W1810 owner manual Collector assembly fastened to Stand, Model W1808-09

Page 22

W1808/W1809/W1810 Cyclone Dust Collectors

SET UP

4.Place a large piece of cardboard on the ground to prevent scrapes from bare concrete for the next steps.

5.Lay the stand assembly on its side and slide the col- lector assembly into the stand assembly.

6.Fasten the collector assembly to the stand with (8) 3/8"-16 x 1" hex bolts, (16) 3/8" flat washers, and (8) 3/8"-16 lock nuts, as shown in Figure 16.

7.Model W1808–W1809: Slide the lower legs onto the upper stand assembly, and fit the lower braces into the leg notches. Fasten the upper and lower legs and lower braces using (24) 3/8"-16 x 3/4" hex bolts,

(16)3/8"-16 x 1" hex bolts, (80) 3/8" flat washers, and (40) 3/8"-16 lock nuts. Refer to the W1808 and W1809 Parts Breakdowns on Pages 48 and 51 for more detail.

Note: On Model W1810, the lower legs will be installed in Step 19, on Page 23.

Note: It will be easier to assemble the lower legs and braces onto the upper stand assembly if you keep the fasteners loose.

8.Place the 3 x 6 x 1800mm roll of foam tape on the intake cylinder, as shown in Figure 18.

Figure 16. Collector assembly fastened to

the stand, Model W1810.

Lower Brace

Lower Leg

Figure 17. Collector assembly fastened to

the stand, Model W1808-09.

Figure 18. Foam tape adhered to intake

cylinder.

-20-

Image 22

Contents

Cyclone Dust Collectors W1808 W1809Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Introduction Introduction Introduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Dust Collectors 220V Operation Electrical SpecificationsExtension Cords Unpacking Items Needed for SetupDescription Qty Collector Box Contents Figures Qty W1808/W1809 Inventory Stand Box Contents Figure Qty Filter Box Contents Figure QtyW1810 Inventory Hardware Box Rubber Handles Bag HolderContents of Filter Boxes Figure Qty Hardware Box CtdAssembly To assemble the dust collector, do these stepsCollector assembly fastened to Stand, Model W1808-09 Intake cylinder attached to Filter cross braces Model W1810 Hoses and noise reducers Installed Model W1810 Attaching foam tape to Collector drum lid Installing latches on collector Latch hooked over lid for Clamping Test Run To test run the cyclone dust collector, do these stepsOperations GeneralRemote Control Duct MaterialFlexible Duct System Design Decide Who Will DesignMachine Approximate Dust Port Size Required CFM MachineDetermining Main Line Duct Size Total CFM Branch Line Size90˚ 45˚ Dia Elbow WyeY Additional Factors Static PressureExample list for totaling static Pressure loss System Grounding Flex-hose grounded toCyclone Dust Collector Accessories Black ABS Plastic Blast Gates Aluminum Blast GatesWire-Reinforced Clear Dust Clear Hose Collection Hose Cleaning Filter Emptying DrumW1808 motor wiring W1808 Electrical ComponentsSee Figures 58 W1808 Wiring DiagramSee Figure W1809 motor wiring W1809 Electrical ComponentsW1809 Wiring Diagram See Figures 61W1810 motor wiring W1810 Electrical ComponentsW1810 Wiring Diagram Troubleshooting Problem Possible Cause Corrective ActionDust collector does not Ducting and ports are Parts W1808 Parts BreakdownW1808 Parts List PART# DescriptionSwitchbase W1809 Parts Breakdown W1809 Parts List Upperstandleg W1810 Parts Breakdown W1810 Parts List PART# DescriptionXPLW04 LOCKWASHER3/8 XPW02 FLATWASHER3/8 W1808-10 Labels and Cosmetic Parts Motor Rear ViewWarranty Warranty Registration CommentsBOX BELLINGHAM, WA