Woodstock W1810, W1809, W1808 owner manual Assembly, To assemble the dust collector, do these steps

Page 21

W1808/W1809/W1810 Cyclone Dust Collectors

Assembly

The following instructions apply to all three models except where noted. To begin assembling the W1810, start at Step 1. To begin assembling the W1808/W1809, start at Step 2.

To assemble the dust collector, do these steps:

1.Model W1810 Only: Connect the upper stand legs with the lower braces, using (16) 3/8"-16 x 3/4" hex bolts, (32) 3/8" flat washers, and (16) 3/8"-16 lock nuts, as shown in Figure 13. Only finger tighten for now.

2.Connect the upper braces to the upper stand legs, using (16) 3/8"-16 x 3/4" hex bolts, (32) 3/8" flat wash- ers, and (16) 3/8"-16 lock nuts, as shown in Figure 14.

Note: On Model W1808/W1809, the lower braces will not be installed until Step 7 on Page 20.

3.Attach the cyclone funnel to the intake barrel with a barrel gasket between the two, as shown in Figure 15, with (12) 5/16"-18 x 1" hex bolts, (24) 5/16" flat washers, and (12) 5/16"-18 hex nuts.

Upper Stand Leg

Lower Brace

Figure 13. Upper stand legs connected to

lower stand braces, Model W1810.

Upper Brace

Figure 14. Upper braces attached to stand

assembly, Model W1810.

Cyclone

Funnel

Intake

Barrel

SET UP

Gasket

Figure 15. Cyclone funnel attached to

intake barrel.

-19-

Image 21

Contents

W1808 W1809 Cyclone Dust CollectorsPage Contents Woodstock Technical Support IntroductionIntroduction Introduction Introduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Dust Collectors Electrical Specifications 220V OperationExtension Cords Items Needed for Setup UnpackingDescription Qty W1808/W1809 Inventory Collector Box Contents Figures QtyFilter Box Contents Figure Qty Stand Box Contents Figure QtyHardware Box Rubber Handles Bag Holder W1810 InventoryHardware Box Ctd Contents of Filter Boxes Figure QtyTo assemble the dust collector, do these steps AssemblyCollector assembly fastened to Stand, Model W1808-09 Intake cylinder attached to Filter cross braces Model W1810 Hoses and noise reducers Installed Model W1810 Attaching foam tape to Collector drum lid Installing latches on collector Latch hooked over lid for Clamping To test run the cyclone dust collector, do these steps Test RunGeneral OperationsDuct Material Remote ControlFlexible Duct Decide Who Will Design System DesignMachine Machine Approximate Dust Port Size Required CFMTotal CFM Branch Line Size Determining Main Line Duct SizeAdditional Factors Static Pressure 90˚ 45˚ Dia Elbow WyeYExample list for totaling static Pressure loss Flex-hose grounded to System GroundingBlack ABS Plastic Blast Gates Aluminum Blast Gates Cyclone Dust Collector AccessoriesWire-Reinforced Clear Dust Clear Hose Collection Hose Emptying Drum Cleaning FilterW1808 Electrical Components W1808 motor wiringW1808 Wiring Diagram See Figures 58See Figure W1809 Electrical Components W1809 motor wiringSee Figures 61 W1809 Wiring DiagramW1810 Electrical Components W1810 motor wiringW1810 Wiring Diagram Problem Possible Cause Corrective Action TroubleshootingDust collector does not Ducting and ports are W1808 Parts Breakdown PartsPART# Description W1808 Parts ListSwitchbase W1809 Parts Breakdown W1809 Parts List Upperstandleg W1810 Parts Breakdown PART# Description W1810 Parts ListXPLW04 LOCKWASHER3/8 XPW02 FLATWASHER3/8 Motor Rear View W1808-10 Labels and Cosmetic PartsWarranty Comments Warranty RegistrationBOX BELLINGHAM, WA