Woodstock W1809, W1808 owner manual Filter cross braces Model W1810

Page 24

W1808/W1809/W1810 Cyclone Dust Collectors

SET UP

14.Attach the outlet port and filter L-braces to the housing with the outlet gasket between, as shown in Figures 23 & 24 using the fasteners below.

—Model W1810: Use (10) 5/16"-18 x 1" hex bolts, (20) 5/16" flat washers, and (10) 5/16"-18 hex nuts.

—Model W1809: Use (11) 5/16"-18 x 1" hex bolts, (22) 5/16" flat washers, and (11) 5/16"-18 hex nuts.

—Model W1808: Use (8) 5/16"-18 x 1" hex bolts, (16) 5/16" flat washers, and (8) 5/16"-18 hex nuts.

15.Model W1810 Only: Attach the filter cross braces to the L-braces, as shown in Figure 25, using (4) 3/8"-16 x 3/4" hex bolts, (8) 3/8" flat washers, and (4) 3/8"-16 hex nuts.

16. Using the forklift, lift the entire assembly approxi- mately 2' off the ground to gain clearance for filter installation.

Gasket

Figure 23. Attaching the outlet port and

filter L-braces to the blower housing

(Model W1810).

L-Brace

Figure 24. Filter L-braces atttached to

blower housing (Model W1810).

Cross Braces

Figure 25. Filter cross braces (Model

W1810).

-22-

Image 24

Contents

Cyclone Dust Collectors W1808 W1809Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Introduction Introduction Introduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Dust Collectors Electrical Specifications 220V OperationExtension Cords Items Needed for Setup UnpackingDescription Qty Collector Box Contents Figures Qty W1808/W1809 InventoryStand Box Contents Figure Qty Filter Box Contents Figure QtyW1810 Inventory Hardware Box Rubber Handles Bag Holder Contents of Filter Boxes Figure Qty Hardware Box CtdAssembly To assemble the dust collector, do these stepsCollector assembly fastened to Stand, Model W1808-09 Intake cylinder attached to Filter cross braces Model W1810 Hoses and noise reducers Installed Model W1810 Attaching foam tape to Collector drum lid Installing latches on collector Latch hooked over lid for Clamping Test Run To test run the cyclone dust collector, do these stepsOperations GeneralRemote Control Duct MaterialFlexible Duct System Design Decide Who Will DesignMachine Approximate Dust Port Size Required CFM MachineDetermining Main Line Duct Size Total CFM Branch Line Size90˚ 45˚ Dia Elbow WyeY Additional Factors Static PressureExample list for totaling static Pressure loss System Grounding Flex-hose grounded toCyclone Dust Collector Accessories Black ABS Plastic Blast Gates Aluminum Blast GatesWire-Reinforced Clear Dust Clear Hose Collection Hose Cleaning Filter Emptying DrumW1808 motor wiring W1808 Electrical ComponentsW1808 Wiring Diagram See Figures 58See Figure W1809 motor wiring W1809 Electrical ComponentsW1809 Wiring Diagram See Figures 61W1810 motor wiring W1810 Electrical ComponentsW1810 Wiring Diagram Troubleshooting Problem Possible Cause Corrective ActionDust collector does not Ducting and ports are Parts W1808 Parts BreakdownW1808 Parts List PART# DescriptionSwitchbase W1809 Parts Breakdown W1809 Parts List Upperstandleg W1810 Parts Breakdown W1810 Parts List PART# DescriptionXPLW04 LOCKWASHER3/8 XPW02 FLATWASHER3/8 W1808-10 Labels and Cosmetic Parts Motor Rear ViewWarranty Warranty Registration CommentsBOX BELLINGHAM, WA