Woodstock W1816 owner manual Upper stand brace connected To the upper stand legs

Page 17

W1816 Owner's Manual (Mfg. Since 10/09)

8. Connect the two upper stand braces to the upper
stand legs with (4) 3⁄8"-16 x 3⁄4" hex bolts and (4) 3⁄8"	Upper Stand Brace
flat washers, as shown in Figure 13.	x 2
	x 2

Note: Orient the braces so that the off-center third hole is aligned with the two mounting holes in the blower housing bracket, as shown in Figure 13. These mounting holes are for attaching the remote magnetic switch in the next step.

Align

These

Holes

9.Attach the remote switch assembly to the blower housing bracket and upper stand brace with (3) 3⁄8"- 16 x 3⁄4" hex bolts and (3) 3⁄8" flat washers, as shown in Figure 14.

Note: You may attach the switch assembly to either side of the blower housing. Keep in mind that you must have a line-of-sight between the remote controller and the switch for proper operation. Refer to Remote Control on Page 24 for additional information.

Figure 13. Upper stand brace connected

to the upper stand legs.

x 3

Figure 14. Remote magnetic switch

attached.

SETUP

10.Slide the four stand leg connectors onto the upper stand legs, then connect them with (16) 3⁄8"-16 x

3⁄4" hex bolts and (16) 3⁄8" flat washers, as shown in

Figure 15.

Leg

Connector

x 16

Figure 15. Stand leg connector attached

to the upper stand leg.

-15-

Image 17

Contents

Model W1816 OWNERS MANUALPage Contents Woodstock Technical Support IntroductionMachine Specifications Machine Dimensions Controls and Features Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Dust Collectors Electrical Electrical Specifications220V Operation Extension CordsUnpacking SetupInventory Inventory Figures Qty Hardware & Miscellaneous Items not shown Inventory Figure Qty Inventory Figure Bolting to Concrete Floors Machine PlacementMounting to Shop Floor To assemble your dust collector, do these steps AssemblyTools & Items Needed Qty Intake barrel attached to Blower housing Vacuum Pipe Upper stand brace connected To the upper stand legs Side stand braces attached Bag platform connected to Side stand brace Crank Arm Installing the drum seal Installing the collection drum Inserting the plastic collection Bag Latch Collection and vacuum hoses Installed To test run the machine, do these steps Test RunGeneral OperationsRemote Control Magnetic SwitchTimer Indicator Lights Turns on when that timer Basic ControlsMetal Duct Ducting MaterialsPlastic Duct Flexible DuctDecide Who Will Design System DesignSketch Your Shop Layout Sketch a Basic Duct LayoutMachine Approximate Determine CFM of Each MachineAverage Dust Port Size MachineDetermining Branch Line Duct Diameter Determining Main Line Duct DiameterCalculating Duct Resistance Multiple Dust PortsTwo Machines on Same Branch Line Seasoned well used Dust Collection Filter Additional Factors Static PressureClosest CFM Metal Duct System GroundingDust Collector Accessories AccessoriesW1006- 3 OD W1141- 3 OD W1007- 4 OD W1142- 4 OD W1008- 5 OD Plastic Blast GatesW1009- 6 OD Shop Fox W1050 Dust Collection Basics Handbook Shop Fox W1003 Floor SweepLubrication MaintenanceEmptying Drum Removing Canister Filter Cleaning Canister FilterRinsing Canister Filter Tools Needed QtyTroubleshooting ServiceWiring Diagram Color KEY Electrical Safety InstructionsStop Wiring DiagramMagnetic switch wiring Motor Junction Box Capacitors Wiring ComponentsMain PartsDescription Main Parts ListVolt Machine Labels FrontMachine Labels Rear Page Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools