Grizzly G0583Z owner manual Service, Troubleshooting

Page 26

SECTION 8: SERVICE

Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel- ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663.

trubble

Troubleshooting

Symptom

Possible Cause

Possible Solution

Machine does not

1.

Wall fuse/circuit breaker is blown/tripped.

1.

Ensure circuit size is suitable for this machine;

start or a breaker

 

 

 

replace weak breaker.

trips.

2.

Power supply switched OFF or is at fault.

2.

Ensure power supply is switched on; ensure power

 

 

 

 

 

supply has the correct voltage.

 

3.

Wiring is open/has high resistance.

3.

Check for broken wires or disconnected/corroded

 

 

 

 

connections, and repair/replace as necessary.

 

4.

Motor ON/OFF switch is at fault.

4.

Replace faulty ON/OFF switch.

 

5.

Motor is at fault.

5.

Test/repair/replace.

 

 

 

 

 

Machine has

1.

Motor or component is loose.

1.

Inspect/replace stripped or damaged bolts/nuts, and

vibration or noisy

 

 

 

re-tighten with thread locking fluid.

operation.

2.

Motor mount loose/broken.

2.

Tighten/replace.

 

 

3.

Machine is incorrectly mounted or sits

3.

Tighten/replace anchor studs in floor if mounted;

 

 

unevenly.

 

chock machine casters if mobile.

 

4.

Motor fan is rubbing on fan cover.

4.

Replace dented fan cover; replace loose/damaged

 

 

 

 

fan.

 

5.

Motor bearings are at fault.

5.

Test by rotating shaft; rotational grinding/loose shaft

 

 

 

 

requires bearing replacement.

 

6.

Impeller is damaged and unbalanced.

6.

Disconnect dust collector from power, and inspect

 

 

 

 

the impeller for dents, bends, loose fins. Replace

 

 

 

 

impeller if any damage is found.

 

7.

Impeller is loose on the motor shaft.

7.

Replace the motor and impeller as a set if the motor

 

 

 

 

shaft and the impeller hub are damaged.

 

 

 

 

 

-24-

Model G0583Z (Mfg. 3/09+)

Image 26
Contents Model G0583Z Dust Collector Page Table of Contents Contact Info IntroductionManual Accuracy Machine DescriptionG0583Z Identification Model G0583Z identification Model G0583Z Mfg /09+Machine Data Sheet Canister Information Wearing Proper APPAREL. Do not wear SafetySafety Instructions for Machinery Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety for Dust Collectors Plug & Outlet Circuit Requirements110/220V Operation ForUnpacking SetupNeeded for Setup Description QtyBox 2 Figure Qty G0583Z InventoryBox 1 Figure Qty Hardware Recognition Chart To assemble your dust collector G0583Z AssemblySite Considerations Canister filter installed and secured Model G0583Z Mfg /09+ Dust collection bag installed Test Run To test run the machineMaterial Selection Collection SystemGeneral System Grounding Plastic Rigid DuctDucting Tips Operations Accessories T23129-Extra 1 Micron Canister For G0583ZSchedule MaintenanceBag Cleaning LubricationEmptying/Replacing Bags To replace the collection bagService TroubleshootingSuction, and rework ducting without sharp bends G0583Z Wiring Diagram Motor junction box wiring Model G0583Z Mfg /09+Parts G0583Z Main BreakdownG0583Z Main Parts List DescriptionCanister Filter Breakdown & List G0583Z Labels Breakdown & List Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY