Guía de Diagnóstico de Averías, Clavos | Campbell Hausfeld HDN23200

100 psi MAX.

Operating Instructions

Model HDN23200

Manual de Instrucciones

Modelo HDN23200

General Safety Information (Continued)

GENERAL

●To reduce the risk of electrical shock, fire, and personal injury, read all the instructions before using the tool.

●Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The tool is able to create sparks resulting in the ignition of dust or fumes.

●Keep bystanders, children, and visi- tors away while operating the tool. Distractions are able to result in the loss of control of the tool.

must be used for the applicable con- ditions.

●Do not attach the hose or tool to your body. Attach the hose to the structure to reduce the risk of loss of balance if the hose shifts.

●Always assume that the tool con- tains fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not.

Guía de Diagnóstico de Averías

!ADVERTENCIA Deje de usar la herramienta inmediatamente si alguno de los siguientes problemas ocurre. Podría resultar en heridas graves. Cualquier reparación o reemplazo de piezas los debe hacer un

técnico calificado de servicio o un centro autorizado de servicio.

Problema	Causa	Solución
Hay una fuga de aire en el	Los anillos en O de la cubierta de la válvula	Debe reemplazar los anillos en O y chequear el funcio-
área de la válvula del gatillo	del gatillo están dañados	namiento del elemento de funcionamiento al contacto
Hay una fuga de aire entre	Los tornillos de la cubierta están flojos	Debe apretar los tornillos

●Read and understand tool labels and manual. Failure to follow warnings, dangers, and cautions could result in DEATH or SERIOUS INJURY.

●Use only a pressure- regulated com-

pressed air source to limit the air pressure supplied to the tool. The regulated pres-

sure must not exceed 100 psi. If the regulator fails, the pressure deliv- ered to the tool must not exceed 200 psi. The nailer could explode which will cause death or serious personal injury.

●Do not make any modifications to the tool without first obtaining written approval from Campbell Hausfeld. Do not use the nailer if any shields or guards are removed or altered. Do not use the nailer as a hammer. Personal injury or tool

damage may occur.

WORK AREA

●Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risk of electrical shock, fire, and personal injury.

PERSONAL SAFETY

●Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influ- ence of drugs, alcohol, or medica- tion. A moment of inattention while operating the tool increases the risk of injury.

●Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair increas- es the risk of injury as a result of being caught in moving parts.

●Avoid unintentional starting. Be sure the switch is off before connecting to the air supply. Do not carry the tool with your finger on the switch or connect the tool to the air supply with the switch on.

●Do not overreach.

Keep proper foot- ing and balance at all times. Proper footing and bal-

ance enables bet-

ter control of the tool in unexpected situations.

●Use safety equipment. A dust mask, non-skid safety shoes and a hard hat

! WARNING

Do not drive a fas- tener on top of other fasteners. The fastener could

glance and cause

death or a serious puncture wound.

Remove finger

! WARNING from the trigger when not driving fasteners. Never carry the tool with your finger on trigger; the tool is able to fire a fastener.

●Never place hands or any other body parts in the fastener

discharge area of the tool. The tool might eject a fastener and could result in death or serious personal injury.

●Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, exam- ine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur.

la cubierta y la boquilla	Los anillos en O están dañados	Debe reemplazar los anillos en O
	La cubierta está dañada	Debe reemplazar la defensa
Hay una fuga de aire entre	Los tornillos están flojos	Debe apretar los tornillos
la cubierta y la tapa	El empaque está dañado	Debe reemplazar el empaque
La herramienta deja de	La cubierta está desgastada	Debe reemplazar la cubierta
clavar un sujetador	La boquilla está sucia	Debe limpiar el canal del sistema de impulso
	La suciedad o daños evitan el	Debe limpiar el cargador
	desplazamiento libre de los sujetadores o
	el mecanismo de impulso en el cargador
	El resorte del mecanismo de impulso está	Debe reemplazar el resorte
	dañado
	El flujo de aire hacia la herramienta es	Cheque las conexiones, la manguera o el compresor
	inadecuado
	El anillo en O del pistón está desgastado o le	Debe reemplazar los anillos en O. Lubríquelos.
	falta lubricación
	Los anillos en O de la válvula del gatillo	Debe reemplazar los anillos en O
	están dañados
	Hay fugas de aire	Debe apretar los tornillos y las conexiones
	Hay una fuga en el empaque de la tapa	Debe reemplazar el empaque
La herramienta funciona	La herramienta no está bien lubricada	Necesita lubricar la herramienta
lentamente o pierde su	El resorte de la tapa del cilindro está roto	Debe reemplazar el resorte
potencia	El orificio de salida de la tapa está obstruído	Debe reemplazar las partes internas dañadas
Hay sujetadores atascados	La guía del mecanismo de impulso está	Debe reemplazar la guía
en la herramienta	desgastada
	Los sujetadores no son del tamaño adecua-	Debe usar los sujetadores recomendados para esta
	do.	herramienta
	Los sujetadores están doblados	Reemplácelos con sujetadores en buenas condiciones
	Los tornillos del cargador o de la boquilla están	Debe apretar los tornillos

Tool Components And Specifications

Cap exhaust

flojos
El mecanismo de impulso está dañado	Debe reemplazar el mecanismo de impulso de sujeta-
	dores

• REQUIRES: 0.8 SCFM with 10 fas-

teners per minute @ 90 psi

• AIR INLET: 1/4” NPT

• FASTENER SIZE RANGE: 3/8” to

1 1/4”

• MAGAZINE CAPACITY:

100 fasteners per load, 18 gauge

• STAPLES: 1/4” crown

• WEIGHT: 2 lbs., 10 oz.

• LENGTH: 9 1/2”

• HEIGHT: 7 1/2”

• MAXIMUM PRESSURE: 100 psi

English

Warning

Label

Date code

Trigger

Latch button

Sujetadores

Clavos

Estos clavos para acabado de Campbell Hausfeld los puede comprar en su tienda más cercana. Si necesita ayuda para encontrar un artículo, comuníquese al 1-800-543-6400. Los clavos de Campbell Hausfeld cumplen o exceden el estándar ASTM F1667

Modelo #	Longitud	Calibre	Acabado	Cabeza	Unión	Clavos por	Clavos por
Modelo #	Longitud	del cuerpo	Acabado	Cabeza	Unión	línea	Caja
		del cuerpo				línea	Caja
FB001600	15,9mm (5/8”)	Calibre 18	Galvanizado	De puntilla/Café	Adhesivo	100	5000
FB002000	19,1mm (3/4”)	Calibre 18	Galvanizado	De puntilla/Café	Adhesivo	100	5000
FB002500	25,4mm (1”)	Calibre 18	Galvanizado	De puntilla/Café	Adhesivo	100	5000
FB003000	31,8mm (11⁄4”)	Calibre 18	Galvanizado	De puntilla/Café	Adhesivo	100	5000

Información de intercambio

• PRESSURE RANGE: 60 - 100 psi

Work contact element (WCE)

Fastener discharge area

Magazine

Los clavos usados con la HDN23200 también se pueden usar con las clavadoras : Bostitch T31-1, T29-30, BT-35, Duofast BB4440, Hitachi NT45A , Paslode 2138-F18 , Porter Cable BN125, BN200, Sears 18309, y Senco SLP20, LS2, LS5.

7-Sp

HDN23200 specifications

The Campbell Hausfeld HDN23200 is an impressive addition to the world of portable air compressors, designed for both home and professional use. This compact unit stands out due to its efficient performance, versatility, and user-friendly features, making it an essential tool for various applications, including inflation, nailing, and painting.

One of the main features of the HDN23200 is its powerful motor, which delivers a robust 3.5 CFM at 90 PSI. This capability ensures that the compressor can handle a wide range of pneumatic tools, providing the necessary air pressure for optimal performance. Its 2.5-gallon tank offers a perfect balance between portability and air supply, allowing users to work for extended periods before needing to recharge the tank.

In terms of design, the HDN23200 boasts a lightweight and compact structure that makes it easy to transport. Weighing in at just over 20 pounds, this air compressor is equipped with a sturdy handle, facilitating ease of movement around the job site or workshop. Its durable plastic housing helps protect internal components and increase the unit's longevity, ensuring it withstands the rigors of daily use.

The Campbell Hausfeld HDN23200 features a low noise level, which happens to be a significant advantage for those working in noise-sensitive environments. Working at just 68 decibels, users can work comfortably without the constant distraction and discomfort often associated with traditional air compressors.

Another key technology included in the HDN23200 is its oil-free pump, which minimizes maintenance requirements and eliminates the need for oil changes. This adds to the convenience of the compressor, as users can focus more on their projects rather than spending time on upkeep.

The easy-to-read gauges on the unit provide accurate monitoring of pressure levels, enabling users to make adjustments quickly and ensure their tools are running at peak efficiency. Additionally, the integrated safety features and thermal overload protection prevent potential damage due to overheating or overuse.

In summary, the Campbell Hausfeld HDN23200 air compressor is a versatile and user-friendly tool, characterized by its compact design, powerful motor, oil-free pump, and low noise operation. These features make it an excellent choice for both DIY enthusiasts and professionals alike, ensuring reliable performance for a variety of air-powered applications. Whether you need to inflate tires, power pneumatic tools, or tackle light spraying tasks, the HDN23200 is equipped to handle the job with efficiency and ease.