Carrier 38AN,BK specifications Microprocessor Control Operation --This sys, Heat

Page 15

o_

o

2S _ -,_

III

m

ON/OFF'"---"

BUTTON

Fig. 14 --Remote Controller

 

 

START

COOL*

 

START

 

COC_.ING.

DIRECT

 

 

 

HEA'i3NG - DIRECT

 

 

 

 

LOUVI_RS

SO AIR

 

 

 

 

LOIJVERS$O AIR

 

 

 

 

 

 

BLOWSDOWN

OU'T HORIZONTAL

 

 

 

 

VERTICAL

 

 

 

 

_ISCHARGE)

DISCHARGE)

 

 

 

 

 

 

 

 

 

 

SWIN G

 

 

 

 

 

BLOWSSTRAIGHT

_

SWING

_

 

is"

 

Pd_IGE_'_

 

 

 

RANGE

HEAT

*Potential range. tDesirable range.

NOTE: Unit is equipped with manual air vents which direct the air

from side to side. Up and down louver motion can be selected using the remote controller. For maximum comfort, set louvers within the

swing range, See Adjusting Airflow section on page 14 for more information.

Fig. 15 --Louver Adjustments

Operating Fault Diagnosis --The system includes

an automatic diagnosis feature which is activated under dif- ficult or unacceptable operating conditions. If such condi- tions occur, the system stops automatically, the operating fault signal appears (green "UNIT ON" light on the front of the fan coil unit flashes), and an analysis of the system operat- ing conditions is initiated. The system will then be restarted automatically, as soon as normal conditions have been re- stored, or it will remain off. If the system does not start again, the green "UNIT ON" light will flash an error code.

Microprocessor Control Operation --This sys-

tem is controlled by a microprocessor designed to give op- timum levels of comfort and operating et_ciency. The con- trol is located in the 40QN unit. To operate the unit, the factory- supplied remote controller is required.

There are 9 (QNB systems) or 12 (QNE/H systems) op- erating modes (including the off mode) for the unit. Each mode operates as follows:

•Off Mode -- When the unit is in the Off mode, all func- tions (compressor, outdoor fan, indoor fan, and air sweep)

are off, except the reversing valve (QNE/H only), which will stay deenergized if the unit was last operated in the Cooling mode.

Air Circulation Mode (Fan Operation Only) -- When Air Circulation mode is selected, the indoor fan will operate continuously in the selected speed (high, medium, low, or auto.). If the Auto. mode is selected, the indoor fan will operate at low speed. The compressor and outdoor fan are off. The reversing valve (QNE/H only) will remain in the last operating mode.

Cooling Mode -- When the Cooling mode is selected, the indoor fan will operate continuously at the selected speed if the speed is high, medium, or low. lfthe indoor fan is in Auto. mode, the fan will change operating speeds de- pending on the difference between the room temperature and the set point. The reversing valve (QNE/H only) will be energized. The compressor cannot ran for 3 minutes from the time the system starts up or for 3 minutes from the time the compressor last operated, when the tempera- ture of the room is equal to or greater than the selected temperature, the compressor and outdoor fan will operate until the room temperature is 2 ° F below the set point, and then shut off. When the room temperature is less than the

selected temperature, the compressor and outdoor fan re- main off.

•Maximum Dehumidification Mode -- When the Dehu- midification mode is selected, the indoor fan will operate continuously at the selected speed if the speed is high, me- dium, or low. If the indoor fan is in Auto. mode, the fan will change operating speeds depending on the room tam- perature. If the room temperature is below the set point, the indoor fan will run at ultra-low speed, and the com- pressor could run for up to 4 minutes. (Ultra-low speed is a control-driven speed [not user configurable] used to sample the space when the fan would normally be off.) The re- versing valve (QNE/H only) will be energized. The com- pressor cannot run for 3 minutes from the time the system starts up or for 3 minutes from the time the compressor last operated.

Initial Operation -- When the mode is first selected, one of the following occurs:

1.If the room temperature is above or equal to the selected temperature, the unit will operate for 16 minutes, and the compressor and outdoor fan will operate. The indoor fan will operate as in the Cooling mode. After 16 minutes of operation (or when the room reaches 2 ° F below set point),

the unit switches to normal dehumidification operation.

2.If the room temperature is below the selected tempera- ture, the unit will operate for 8 minutes as follows: the compressor and outdoor fan will operate for 3 minutes. The indoor fan will operate in low speed, and 30 seconds after the compressor stops, the indoor fan stops. The unit remains off for 1 minute, and then the indoor fan starts in ultra-low speed for 30 seconds. The unit then switches to

normal dehumidification operation.

Normal Operation -- One of the following will take place:

1.when the temperature of the room is equal to or greater than the selected temperature (by not more than 3 ° F), the unit will operate for 8 minutes as follows: the compres- sor and outdoor fan will operate for 3 minutes. The in- door fan will operate in low speed, and 30 seconds after the compressor stops, the indoor fan stops. The unit re- mains off for 1 minute, and then the indoor fan starts in ultra-low speed for 30 seconds. The normal dehumidifi- cation operation is repeated for the newly sensed room temperature.

2.If the room temperature is equal to or greater than the selected temperature, but not by more than between 4 ° F and 6 ° F, the compressor and outdoor fan operate for 4 minutes. The indoor fan will run at ultra-low speed and

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Service Instructions Heating System Combinations for Indoor Outdoor UnitsSystem Indoor Outdoor Unit CoolingLii High Wall Unit Package ContentsPhysical Data, 40QNB Cooling Only High Wall Units Physical Data, 38AN Cooling Only Condensing UnitsPhysical Data, 38BK009,012 Outdoor Heat Pump Units Unit 38BKRefrigerant Type Operating Weight Physical Data, 40QNEIH Heat Pump High Wall UnitsUnit Ciso,..5s Unit Weightabc 40QN Dimensional DrawingHi--till/I/I System Piston Guide Refrigerant ChargesFig, 6 --Maximum System Line Lengths MAXWall Hole Location For Fan Coil Unit Rear Piping Size 009 Shown?q,ElldIi Flare NUT Tube Torque Flare Nut Tightening TorquePR ,LI-1,II Ij iElectric Heater Data Voltagerange Compressor FANLRA RLA FLA InstallFan Coil Unit Onto Mounting Bracket Service Cover Outdoor UnitIndoor and Outdoor Unit START-UP Wireless Remote Controllers --A wireless remoteHeat Microprocessor Control Operation --This sysWill stop30secondsafterthecompressorstopsAfter Emer --Emergency Outdoorair TemperaturefTo Install or Replace Remote Controller Batteries Cleaning and Maintenance ScheduleTask Monthly Quarterly Yearly Indoor Unit SET Time To Clean Condensate Drains-- Clean all drainsTo Clean Indoor Coil --To clean the coil, remove RemovecoverNO. of Quick System Fault LED Flashes SystemFault CodesMinimum Nominal Maximum Temp Thermistor Ohms Volts -- DC TroubleshootingProblem Potential Source Action 40QN Thermistor PropertiesWireless CONTROLLER*AIRFLOW Wall CAPTo Opendrain RCV Aging CAP CH Comp EMI FMC GNDIFM JEM-A OFM PCB PTCFl I rl Control 38BK009 with 40QNE009 Heat Pump System Wiring Diagram Control PCB A55 Y Page

38AN,BK specifications

The Carrier 38AN,BK is a distinguished model in the world of air conditioning, known for its advanced features, innovative technologies, and exceptional performance. This air conditioning unit is particularly favored for residential and small commercial applications, offering a perfect blend of efficiency, reliability, and comfort.

One of the main features of the Carrier 38AN,BK is its high energy efficiency, which is crucial in today’s eco-conscious environment. With a Seasonal Energy Efficiency Ratio (SEER) rating that often exceeds industry standards, this unit ensures minimal energy consumption while providing powerful cooling capabilities. This not only contributes to lower utility bills but also reduces the overall carbon footprint.

The Carrier 38AN,BK employs advanced cooling technologies that make it a standout choice. One notable feature is its use of a scroll compressor, which operates with fewer moving parts than traditional models, resulting in reduced noise levels and enhanced durability. This compressor design also ensures a smoother operation, translating to consistent temperature control and a more comfortable indoor environment.

Another innovative technology incorporated in the Carrier 38AN,BK is the use of smart controls, allowing users to easily adjust settings and monitor performance through compatible smart devices. This feature adds convenience and flexibility, enabling homeowners to manage their home climate efficiently, even when they are away.

In terms of construction, the Carrier 38AN,BK’s robust design includes a galvanized steel cabinet that is resistant to corrosion and designed to withstand adverse weather conditions. This ensures longevity and reliable performance throughout the year. Additionally, the unit features advanced filtration systems that help improve indoor air quality by reducing allergens and pollutants, further enhancing user comfort.

Furthermore, the Carrier 38AN,BK is designed to operate quietly, making it an ideal choice for bedrooms and other quiet spaces. Its noise reduction features, combined with its energy-saving capabilities, position it as an attractive choice for a wide range of applications.

In summary, the Carrier 38AN,BK air conditioning unit excels in efficiency, advanced technologies, and user-friendly features. Its reliable design and quiet operation make it a top choice for anyone seeking effective and environmentally responsible cooling solutions. As both technology-savvy and eco-friendly, it meets the demands of modern homeowners while delivering exceptional comfort year-round.
Top Page Image Contents