Pentair XLS1000, XLS800, CP12 Thermostat Setting, Thermostat will now be set at 80 degrees F

Page 11

THERMOSTAT SETTING

There are no temperature reading numbers printed on the thermostat dial due to calibration changes from unit to unit. The demand for exact temperatures should be regulated by using a high quality thermometer right in the pool water. Normal temperatures for pools are 78 to 82 degrees F. Spa temperatures are 98 to a maximum of 104 degrees F.

You should place a high quality "tie on type" or a "floating type" thermom- eter directly in the pool or spa water, so you can determine what tempera- ture that is suitable to you. Check the pool temperature occasionally during the heat up time until it has reached the temperature you desire.

Then go to the heater and turn thermostat counter clockwise, to the left, away from warmer, SLOWLY until the unit just shuts off. Therefore, the thermostat will be set exactly at the current temperature shown on your floating thermometer. Make a mark on the thermostat dial so you know the approximate setting that you desire.

 

50˚F

 

 

 

104˚F

 

 

 

 

 

 

Min.

 

 

 

 

 

 

Max.

 

 

 

 

+ or - 1.5˚F

 

 

 

 

 

 

 

 

Thermometer

 

 

If the pool temperature on the thermometer reads 80 degrees F, and

 

you turn the thermostat to the "left" until the heater shuts off, the

 

thermostat will now be set at 80 degrees F.

 

 

 

Now the heater will come on each day when the circulation pump starts, then it will bring the pool up to that set temperature. The pool will lose some heat overnight but will come back up to temperature with minimal delay. If you have a pool and spa combination, you can set the spa thermostat the same way once you are in the spa heating mode. When adjusting the thermostat, remember that it will take some time for the water temperature to reach a higher setting. The cooler the outside air, the longer heat up time needed.

CAUTION

MAKE SURE YOU ADJUST THE THERMOSTAT BACK FROM THE HIGHEST POSITION SET DURING THE START UP PROCEDURE OR THE POOL MAY GET TOO WARM. BE SURE TO RESET THE CIRCU- LATION PUMP TIMER FOR 6 TO 18 HOURS PER DAY OR AS NEEDED, ACCORDING TO THE SIZE OF YOUR POOL AND WEATHER CONDITIONS. COLDER CLIMATES WILL REQUIRE MORE TIME. LARGER POOLS WILL REQUIRE MORE TIME. EXPOSED POOLS WILL REQUIRE MORE TIME. WIN- TER TIME OPERATION WILL REQUIRE MORE OPERATIONAL TIME EACH DAY.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Revision #A HydroTemp Manufacturing Co., Inc For Your Safety Read Before OperatingOwners Section Table of Contents Longer Swimming Season LOW MaintenanceReturn on Investment Heat Pump EfficiencyWith 410-A, the safe Clean refrigerantInch Plumbing With Internal Automatic Bypass Up To 90 GPM Trane CompressorAutomatic Design AdvantagesInternal D. Status Lights Dual Thermostat Control PanelThermostat D. Status Light PanelD. Status Light Panel To use indicator lights see Troubleshooting guide pages 26Turn T-STAT ALL the WAY Down Compressor Time DelayAdvise Your Pool Service CO Clean Filtering System Water Pressure SwitchHeat Exchanger Thermostat Control & Settings Evaporator AIR CoilThermostat Control & Settings for Heat & Cool ModelsSET Thermostat to Maximum Common Mechanical TimerThermostat will now be set at 80 degrees F Thermostat SettingWarm Pool Water Pool Shell Reradiation Convection Evaporation WindPool Surface ConductionTypical Pool Blanket & Roller Controlling Heat LossCovers Save Time & Money Spas Heating TipsCondensation Drains Owners Maintenance & CareSprinklers PlantsWater Piping Leak ? CleaningAIR Flow Roof RUN OFFVacuum & Pressure Leaks Filter Cleaning & CareWater Flow Circulation PumpAutomatic Pool Vacuums Professional ServiceTypical Automatic Pool Cleaner Internal Automatic Bypass See chlorinator Placement guidelinesPlumbing & Water Flow Plumbing ConnectionsStalled with all types of chlorinators to prevent chlorine High Rate Water PumpsChemical resistant check valve and loop must be Heat Exchanger Cross Section Standard Pool Water Balance RequirementsSacrificial Water Fittings Advanced Heat Exchanger DesignChlorines Effect on pH ChlorineVacuum Leaks Protect Heat ExchangerChlorine Migration Absolutely no chemicals in the skimmer Chlorinator PlacementAdding Chemicals No chemicals or chlorine tablets in the skimmerCommercial Feeders Chemical Application for SpasLong Term Freeze Protection / Drain Valve Installation Short Term Freeze Protection ProceduresCondition Possible Cause Possible Remedy Owner Trouble Shooting GuideRisk of electrical shock or electrocution Motor valve. Call your installer for advise. Call Mandatory Bonding to Pool Steel Electrical Wiring SpecificationsUnit Identification HOW to GET Service Glossary of Terms Page Page Page This page is blank This page is blank Heat Pumps

XLS1000, XLS800, XLS600, HP 400, HP 600, HP 800, HP 1000, HP 230, CP12 specifications

Pentair is a recognized leader in providing innovative filtration and pumping solutions, and among its noteworthy offerings are the CP12, HP 400, HP 600, HP 800, HP 1000, HP 230, XLS600, XLS800, and XLS1000 models. Each of these products is designed with unique features and advanced technologies that meet diverse customer needs across various applications.

The Pentair CP12 is a compact and efficient pump designed for residential water management. Known for its ease of installation and reliable performance, the CP12 incorporates a high-efficiency motor that minimizes energy consumption while ensuring effective water circulation.

Moving to the HP series, the HP 400, 600, 800, and 1000 models boast powerful performance characteristics suited for heavy-duty applications. These pumps are engineered with robust materials for longevity and durability. With advanced hydraulic designs, they deliver excellent flow rates and pressure, making them ideal for applications like irrigation, water feature management, and even light industrial use. The HP series also features smart technology that allows for remote monitoring and control, enhancing operational efficiency.

In the mid-range, the HP 230 model offers versatility with its multi-purpose capabilities. Designed for residential and light commercial use, it strikes a perfect balance between performance and energy efficiency, ensuring optimal operation without excessive energy costs.

The XLS series, which includes the XLS600, XLS800, and XLS1000 models, targets larger commercial applications. These models are equipped with cutting-edge technology designed for superior flow and pressure management, making them perfect for high-capacity requirements. Their variable speed operation allows for customizable performance tailored to specific system needs, while advanced monitoring capabilities enhance reliability and maintenance scheduling.

All of these Pentair pumps prioritize environmental responsibility with energy-efficient designs that reduce carbon footprints. Key features across the range include corrosion-resistant materials, thermal protection for added safety, and user-friendly interfaces that simplify operation and monitoring.

In conclusion, Pentair’s CP12, HP series, and XLS series pumps stand out due to their innovative technologies, impressive performance capabilities, and commitment to energy efficiency. Whether for residential or commercial applications, these models cater to a wide range of needs, ensuring customers can find effective solutions for their water management challenges.
Top Page Image Contents