Grizzly G0656 owner manual Maintenance, Schedule, Lubrication, Daily Check, Monthly Check

Page 32

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Daily Check:

•Vacuum all dust on and around the machine.

•Wipe down tables and all other unpainted cast iron with a metal protectant.

•Worn or damaged wires.

•Any other unsafe condition.

Monthly Check:

•V-belt tension, damage, or wear.

•Clean/vacuum dust buildup from inside cabi- net and off motor.

Lubrication

Since all bearings are sealed and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them.

Below is a list of components that require periodic lubrication. Be careful not to over-lubricate these components. Large amounts of lubricant will attract sawdust, causing the metal components to gum up and bind.

Always disconnect power to the machine before lubricating! Failure to do this may result in serious personal injury.

Leadscrews: Lubricate with light machine oil as needed. See the location shown in Figure 46 and Part 23 and 48 on Page 41. Wipe off excess oil and sawdust with a cloth.

Figure 46. Leadscrew lubrication location.

Gibs: Lower the infeed and outfeed table to access the gibs. Annually place a couple drops of oil at the top of each gib and move the tables up and down to distribute the oil. See the locations shown in Figure 47 and Part 66 on Page 41. Wipe off excess oil.

Figure 47. Location to lubricate gibs.

-30-

G0656 8" Jointer with Built-In Mobile Base

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model G0656 Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Circuit Requirements 220V OperationSetup Setup SafetyItems Needed for Setup UnpackingAssembly Fasteners Qty InventoryWood Crate Figure Qty Cardboard Box Figure QtyHardware Recognition Chart Clean Up Site ConsiderationsAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page To set the outfeed table height Dust Collection Setting OutfeedTo connect a dust collection hose Recommended Adjustments Factory adjustments that should be verifiedTest Run Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer G3631-Jointer Knife Hone AccessoriesH7765-8 Byrd Shelix Cutterhead Dispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionMaintenance ScheduleLubrication Daily CheckBelts CleaningTo adjust/replace the V-belt Service TroubleshootingCutting Setting/Replacing Knives Inspecting KnivesTools Needed Qty To inspect the knivesPage Setting Infeed Table Calibrating Depth ScaleTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs Wiring Diagram See FigureTable Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List DescriptionLabel Placement Page Page Warranty and Returns
Top Page Image Contents