Grizzly G1018HW instruction manual Cutterhead Guard, To install the cutterhead guard

Page 27

Cutterhead Guard

To install the cutterhead guard:

1.Locate the spring tang on the cutterhead guard that is shown in Figure 35.

Figure 35. Spring tang on cutterhead guard.

2.Rotate the spring tang approximately half of a turn.

3.Keep tension on the spring tang and install the shaft into the shaft housing on the front of the infeed table as shown in Figure 36.

Figure 36. Installing cutterhead guard while

holding spring tang.

4.Lower the shaft into the shaft housing far enough that the spring tang will rest against the edge of the infeed table when released, as shown in Figure 37.

Figure 37. Spring tang against infeed table.

5.Tighten the lock at the front of the housing.

6.Test the cutterhead guard by moving it toward the front of the jointer and then letting it go. The guard should return back to its original position against the fence and over the cutterhead, or as shown in Figure 38.

This operation is extremely important for operator safety!

Figure 38. Cutterhead guard properly posi- tioned over cutterhead and against fence.

7.If the guard drags across either table, release the lock at the shaft housing and move the guard up a little.

 

 

 

 

 

 

 

 

 

 

 

 

G0500/G1018/G1018HW 8" Jointers

-25-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model G0500/G1018/G1018HW JointersPage Table of Contents Troubleshooting Guide 42-43 Safety Instructions For Power Tools SafetyLength Never Joint end grain Additional Safety Instructions For JointersDescription G0500 G1018 G1018HW Introduction220V Operation Circuit Requirements110V Circuit Breaker Requirements 110V Operation110V Operation GroundingExtension Cords 220V OperationIdentification Common Terms and Definitions SET UP UnpackingG0500 Inventory G1018HW Inventory G1018 InventoryMeasure Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly Switch InstallationTo install the switch To connect the motor cord to the motor Wiring ConnectionTo install the V-belt Jointer to StandBelt Stand Cover To install the stand coverFence to Jointer G0500/G1018HW Handwheel InstallationTo install the fence on the jointer unit To install the handwheels on the Model G0500/G1018HWTo assemble the knife setting gauge G1018 Table Lever InstallationKnife Setting Gauge To install the table levers on the Model G1018HWKnife Inspection Table AlignmentTo inspect the knife height Outfeed table check To adjust the infeed tableG1018 Table Stops To set the Model G1018 outfeed table stop boltTo set the Model G1018 infeed table stop bolt To install the cutterhead guard This operation is extremely important for operator safetyCutterhead Guard To check and adjust the 45˚ R fence stop To check and adjust the 90˚ fence stopFence Stops Test Run Plug InstallationTo check and adjust the 45˚L fence stop To install a plug on your power cordStock Inspection & Requirements OperationsSquaring Stock Illustration of surface planing effects Surface PlaningIllustration of edge jointing effects Edge JointingIllustration of bevel cutting effects Bevel CuttingIllustration of rabbet cutting effects A few sample joints Rabbet CuttingKnife Condition MaintenanceGeneral LubricationDate Approximate Hours Of Use Maintenance Performed To set the knives Service AdjustmentsAbout Service Setting KnivesTable gibs To adjust the table gibs Adjusting GibsTo adjust the V-belt tension Adjusting V-BeltsTo adjust the V-belt alignment Replacing V-BeltTo replace the V-belts Date Approximate Hours Of Use Service Performed Reference Info Symptom Possible Cause Corrective Action Troubleshooting GuideSee G0500/G1018/G1018HW Wiring Diagram Machine Data Sheet G0500 G0500 205 213 209 212 210 204211 202 208 201207 203 206 220 332 Base Cutterhead Model G1018 8 Jointer G1018 126 125 122 121 120 102 104 105 Table ADJ ROD 215 G1018 KNIVES, SET of Three Model G1018HW Jointer W/ Handwheels G1018HW 126 125 122 121 120 102 104 105 Rivet 2 X 5MM 202 205 211 203 204 210 213 209 212 208 207 201 206 214 G1018HW 328 PG1018323 Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog

G1018, G1018HW specifications

The Grizzly G1018HW and G1018 are compact, versatile woodworking machines designed for hobbyists and professionals alike. Known for their robust construction and user-friendly design, these models offer a multitude of features that cater to various woodworking needs.

At the heart of both models is a powerful motor that delivers consistent performance. The G1018HW, being the heavier variant, is built with enhanced durability in mind, making it ideal for users who demand a bit more from their machinery. It boasts an increased weight capacity, ensuring stability during operation, which is particularly beneficial for larger workpieces.

Both models come with an effective dust collection system, crucial for maintaining a clean and safe workspace. The integrated dust port connects easily to standard dust collection hoses, minimizing dust and debris during operation. This feature not only improves visibility but also contributes to overall health safety by reducing airborne particles.

The G1018 and G1018HW are equipped with precision-machined components, ensuring accuracy and reliability in cuts. The adjustable table height and tilt features provide versatility, allowing users to perform a range of operations, from jointing to planing. The intuitive controls and clear scale markings make it easy to set desired measurements without hassle.

Additionally, the machines are designed with portability in mind. Despite their solid build, they come with mobility features such as built-in wheels and handles, making it convenient to move them around the workshop or transport them to different job sites. The compact design fits well into smaller spaces without compromising on function.

Another notable characteristic is the availability of aftermarket accessories, which can enhance functionality further. Users can customize their G1018 models with additional attachments that increase their versatility, allowing them to tackle more complex tasks.

In summary, the Grizzly G1018HW and G1018 are exceptional additions to any woodworking setup. Their powerful motors, effective dust control systems, precision-engineered components, and user-friendly design set them apart in the realm of woodworking machines. Whether for a hobbyist or a seasoned professional, these models provide the practicality and reliability needed to produce high-quality results.
Top Page Image Contents