Grizzly G1018HW instruction manual Maintenance, General, Lubrication, Knife Condition

Page 36

SECTION 7: MAINTENANCE

Disconnect power to the machine when perform- ing any adjustments or maintenance. Failure to do this may result in seri- ous personal injury.

General

Regular periodic maintenance on your Grizzly 8" jointer will ensure its optimum performance. Make a habit of inspecting your jointer each time you use it. Check for the following conditions and repair or replace when necessary.

1.Loose mounting bolts.

2.Worn switch.

3.Worn or damaged cords and plugs.

4.Damaged V-belt.

5.Any other condition that could hamper the safe operation of this machine.

Lubrication

Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them. Table ways and the fence assembly should not be lubricated. If the tables appear to be stuck, dis- assemble and clean any foreign materials from the ways. Re-assemble and reset the gibs.

V-Belt

Inspect regularly for tension and wear. Check the V-belt tension by squeezing them in the center. If you can squeeze them more than 1⁄2" on both sides, using moderate pressure, then they need to be tightened. Check pulleys to ensure that they are properly aligned. To replace or adjust the V- belts, see Section 8: Service Adjustments.

Table

The table and other non-painted surfaces on your Grizzly 8" Jointer should be protected against rust and pitting. Wiping the table clean after every use ensures that moisture from wood dust does not remain on bare metal surfaces.

Tables can be kept rust-free with regular applica- tions of products like SLIPIT® or Boeshield® T-9. For long term storage you may want to consider products like Kleen Bore's Rust Guardit™.

Knife Condition

Using sharp knives is one of the most important factors involved with the operation of the jointer. A good maintenance procedure is to hone the knives to keep them in top shape. A knife hone will polish and finely sharpen jointer knives quick- ly and easily without removing them.

For damaged or extra dull knives, have them resharpened by a professional grinder. To avoid downtime from resharpening, we recommend having an extra set of knives on hand.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-34-

 

 

 

G0500/G1018/G1018HW 8" Jointers

 

 

 

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Jointers Model G0500/G1018/G1018HWPage Table of Contents Troubleshooting Guide 42-43 Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Jointers Never Joint end grainIntroduction Description G0500 G1018 G1018HWCircuit Requirements 220V Operation110V Operation 110V Circuit Breaker RequirementsGrounding Extension Cords220V Operation 110V OperationIdentification Common Terms and Definitions SET UP UnpackingG0500 Inventory G1018 Inventory G1018HW InventoryHardware Recognition Chart MeasureClean Up Site ConsiderationsBeginning Assembly Switch InstallationTo install the switch Wiring Connection To connect the motor cord to the motorTo install the V-belt Jointer to StandBelt To install the stand cover Stand CoverG0500/G1018HW Handwheel Installation To install the fence on the jointer unitTo install the handwheels on the Model G0500/G1018HW Fence to JointerG1018 Table Lever Installation Knife Setting GaugeTo install the table levers on the Model G1018HW To assemble the knife setting gaugeKnife Inspection Table AlignmentTo inspect the knife height To adjust the infeed table Outfeed table checkG1018 Table Stops To set the Model G1018 outfeed table stop boltTo set the Model G1018 infeed table stop bolt To install the cutterhead guard This operation is extremely important for operator safetyCutterhead Guard To check and adjust the 45˚ R fence stop To check and adjust the 90˚ fence stopFence Stops Plug Installation To check and adjust the 45˚L fence stopTo install a plug on your power cord Test RunOperations Stock Inspection & RequirementsSquaring Stock Surface Planing Illustration of surface planing effectsEdge Jointing Illustration of edge jointing effectsBevel Cutting Illustration of bevel cutting effectsRabbet Cutting Illustration of rabbet cutting effects A few sample jointsMaintenance GeneralLubrication Knife ConditionDate Approximate Hours Of Use Maintenance Performed Service Adjustments About ServiceSetting Knives To set the knivesAdjusting Gibs Table gibs To adjust the table gibsAdjusting V-Belts To adjust the V-belt tensionTo adjust the V-belt alignment Replacing V-BeltTo replace the V-belts Date Approximate Hours Of Use Service Performed Reference Info Troubleshooting Guide Symptom Possible Cause Corrective ActionSee G0500/G1018/G1018HW Wiring Diagram Machine Data Sheet G0500 G0500 205 213 209 212 210 204211 202 208 201207 203 206 220 332 Base Cutterhead Model G1018 8 Jointer G1018 126 125 122 121 120 102 104 105 Table ADJ ROD 215 G1018 KNIVES, SET of Three Model G1018HW Jointer W/ Handwheels G1018HW 126 125 122 121 120 102 104 105 Rivet 2 X 5MM 202 205 211 203 204 210 213 209 212 208 207 201 206 214 G1018HW 328 PG1018323 Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog

G1018, G1018HW specifications

The Grizzly G1018HW and G1018 are compact, versatile woodworking machines designed for hobbyists and professionals alike. Known for their robust construction and user-friendly design, these models offer a multitude of features that cater to various woodworking needs.

At the heart of both models is a powerful motor that delivers consistent performance. The G1018HW, being the heavier variant, is built with enhanced durability in mind, making it ideal for users who demand a bit more from their machinery. It boasts an increased weight capacity, ensuring stability during operation, which is particularly beneficial for larger workpieces.

Both models come with an effective dust collection system, crucial for maintaining a clean and safe workspace. The integrated dust port connects easily to standard dust collection hoses, minimizing dust and debris during operation. This feature not only improves visibility but also contributes to overall health safety by reducing airborne particles.

The G1018 and G1018HW are equipped with precision-machined components, ensuring accuracy and reliability in cuts. The adjustable table height and tilt features provide versatility, allowing users to perform a range of operations, from jointing to planing. The intuitive controls and clear scale markings make it easy to set desired measurements without hassle.

Additionally, the machines are designed with portability in mind. Despite their solid build, they come with mobility features such as built-in wheels and handles, making it convenient to move them around the workshop or transport them to different job sites. The compact design fits well into smaller spaces without compromising on function.

Another notable characteristic is the availability of aftermarket accessories, which can enhance functionality further. Users can customize their G1018 models with additional attachments that increase their versatility, allowing them to tackle more complex tasks.

In summary, the Grizzly G1018HW and G1018 are exceptional additions to any woodworking setup. Their powerful motors, effective dust control systems, precision-engineered components, and user-friendly design set them apart in the realm of woodworking machines. Whether for a hobbyist or a seasoned professional, these models provide the practicality and reliability needed to produce high-quality results.
Top Page Image Contents