Grizzly G1018HW instruction manual Bevel Cutting, Illustration of bevel cutting effects

Page 34

Bevel Cutting

The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece. See Figure 48.

The Grizzly 8" Jointers have preset fence stops at 45˚ to the left and 45˚ to the right. If your situation requires a different angle, the preset fence stops can be easily adjusted for your needs.

Figure 48. Illustration of bevel cutting effects.

NOTICE

If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation.

To bevel cut on the jointer:

1.Make sure that you have read and under- stand all safety instructions in Section 1: Safety and that your stock has been inspect- ed for safe operation as described in the “Stock Inspection” instructions earlier in this section.

2.Make sure your workpiece is within the mini- mum and maximum stock dimensions that your Grizzly 8" Jointer can safely process. (Check the data sheet in the back of this manual for your particular model.)

3.Set the cutting depth for your operation. (We suggest between 1⁄16" and 1⁄8" for bevel cut- ting, using a more shallow depth for harder wood species or for wider stock.)

4.Make sure your fence is set to the angle of your desired cut.

5.If your workpiece is cupped (warped), place it so the concave side is face down on the surface of the infeed table.

6.Start the jointer.

7.With a push block in your leading hand, press the workpiece against the table and fence with firm pressure.

8.Feed the workpiece over the cutterhead as shown in Figure 49. Note—If your leading hand gets within 4" of the cutterhead, lift it up and over the cutterhead, and place the push block on the portion of the workpiece that is over the outfeed table. At this point, focus your pressure on the outfeed end of the workpiece while feeding, and repeat the same action with your trailing hand when it gets within 4" of the cutterhead. To keep your hands safe, DO NOT let them get clos- er than 4" from the cutterhead when it is moving!

9.Repeat steps 7-8until the angled cut is sat- isfactory to your needs.

Figure 49. Bevel cutting with the fence at 45˚.

-32-

G0500/G1018/G1018HW 8" Jointers

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Jointers Model G0500/G1018/G1018HWPage Table of Contents Troubleshooting Guide 42-43 Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Jointers Never Joint end grainIntroduction Description G0500 G1018 G1018HWCircuit Requirements 220V Operation110V Operation 110V Circuit Breaker Requirements220V Operation GroundingExtension Cords 110V OperationIdentification Common Terms and Definitions Unpacking SET UPG0500 Inventory G1018 Inventory G1018HW InventoryHardware Recognition Chart MeasureClean Up Site ConsiderationsSwitch Installation Beginning AssemblyTo install the switch Wiring Connection To connect the motor cord to the motorJointer to Stand To install the V-beltBelt To install the stand cover Stand CoverTo install the handwheels on the Model G0500/G1018HW G0500/G1018HW Handwheel InstallationTo install the fence on the jointer unit Fence to JointerTo install the table levers on the Model G1018HW G1018 Table Lever InstallationKnife Setting Gauge To assemble the knife setting gaugeTable Alignment Knife InspectionTo inspect the knife height To adjust the infeed table Outfeed table checkTo set the Model G1018 outfeed table stop bolt G1018 Table StopsTo set the Model G1018 infeed table stop bolt This operation is extremely important for operator safety To install the cutterhead guardCutterhead Guard To check and adjust the 90˚ fence stop To check and adjust the 45˚ R fence stopFence Stops To install a plug on your power cord Plug InstallationTo check and adjust the 45˚L fence stop Test RunOperations Stock Inspection & RequirementsSquaring Stock Surface Planing Illustration of surface planing effectsEdge Jointing Illustration of edge jointing effectsBevel Cutting Illustration of bevel cutting effectsRabbet Cutting Illustration of rabbet cutting effects A few sample jointsLubrication MaintenanceGeneral Knife ConditionDate Approximate Hours Of Use Maintenance Performed Setting Knives Service AdjustmentsAbout Service To set the knivesAdjusting Gibs Table gibs To adjust the table gibsAdjusting V-Belts To adjust the V-belt tensionReplacing V-Belt To adjust the V-belt alignmentTo replace the V-belts Date Approximate Hours Of Use Service Performed Reference Info Troubleshooting Guide Symptom Possible Cause Corrective ActionSee G0500/G1018/G1018HW Wiring Diagram Machine Data Sheet G0500 G0500 205 213 209 212 210 204211 202 208 201207 203 206 220 332 Base Cutterhead Model G1018 8 Jointer G1018 126 125 122 121 120 102 104 105 Table ADJ ROD 215 G1018 KNIVES, SET of Three Model G1018HW Jointer W/ Handwheels G1018HW 126 125 122 121 120 102 104 105 Rivet 2 X 5MM 202 205 211 203 204 210 213 209 212 208 207 201 206 214 G1018HW 328 PG1018323 Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog

G1018, G1018HW specifications

The Grizzly G1018HW and G1018 are compact, versatile woodworking machines designed for hobbyists and professionals alike. Known for their robust construction and user-friendly design, these models offer a multitude of features that cater to various woodworking needs.

At the heart of both models is a powerful motor that delivers consistent performance. The G1018HW, being the heavier variant, is built with enhanced durability in mind, making it ideal for users who demand a bit more from their machinery. It boasts an increased weight capacity, ensuring stability during operation, which is particularly beneficial for larger workpieces.

Both models come with an effective dust collection system, crucial for maintaining a clean and safe workspace. The integrated dust port connects easily to standard dust collection hoses, minimizing dust and debris during operation. This feature not only improves visibility but also contributes to overall health safety by reducing airborne particles.

The G1018 and G1018HW are equipped with precision-machined components, ensuring accuracy and reliability in cuts. The adjustable table height and tilt features provide versatility, allowing users to perform a range of operations, from jointing to planing. The intuitive controls and clear scale markings make it easy to set desired measurements without hassle.

Additionally, the machines are designed with portability in mind. Despite their solid build, they come with mobility features such as built-in wheels and handles, making it convenient to move them around the workshop or transport them to different job sites. The compact design fits well into smaller spaces without compromising on function.

Another notable characteristic is the availability of aftermarket accessories, which can enhance functionality further. Users can customize their G1018 models with additional attachments that increase their versatility, allowing them to tackle more complex tasks.

In summary, the Grizzly G1018HW and G1018 are exceptional additions to any woodworking setup. Their powerful motors, effective dust control systems, precision-engineered components, and user-friendly design set them apart in the realm of woodworking machines. Whether for a hobbyist or a seasoned professional, these models provide the practicality and reliability needed to produce high-quality results.
Top Page Image Contents