Grizzly G0500 instruction manual Table of Contents

Page 3

	TABLE OF CONTENTS
		PAGE
1.	SAFETY	3
	Safety Instructions For Power Tools	3-4
	Additional Safety Instructions For Jointers	5
2.	INTRODUCTION	6
3.	CIRCUIT REQUIREMENTS	7
	220V Operation	7
	110V Operation	8
	Grounding	9
	Extension Cords	9
4.	IDENTIFICATION	10-11
	Common Terms and Definitions	11
5.	SETUP	12
	Unpacking	12
	G0500 Inventory	12
	G1018 Inventory	13
	G1018HW Inventory	13
	Hardware Recognition Chart	14
	Clean Up	15
	Site Considerations	15
	Beginning Assembly	16
	Switch Installation	16-17
	Wiring Connection	17
	Jointer Stand	18
	V-Belt	18-19
	Stand Cover	19
	Fence to Jointer	20
	G0500/G1018HW Handwheel Installation	20
	G1018 Table Lever Installation	21
	Knife Setting Gauge	21
	Knife Inspection	22
	Table Alignment	22-23
	G1018 Table Stops	24
	Cutterhead Guard	25
	Fence Stops	26-27
	Plug Installation	27
	Test Run	27
6.	OPERATIONS	28
	Stock Inspection & Requirements	28-29
	Squaring Stock	29
	Surface Planing	30
	Edge Jointing	31
	Bevel Cutting	32
	Rabbet Cutting	33

Image 3

Contents Model G0500/G1018/G1018HW JointersPage Table of Contents Troubleshooting Guide 42-43 Safety Instructions For Power Tools SafetyLength Never Joint end grain Additional Safety Instructions For JointersDescription G0500 G1018 G1018HW Introduction220V Operation Circuit Requirements110V Circuit Breaker Requirements 110V Operation110V Operation GroundingExtension Cords 220V OperationIdentification Common Terms and Definitions SET UP UnpackingG0500 Inventory G1018HW Inventory G1018 InventoryMeasure Hardware Recognition ChartSite Considerations Clean UpBeginning Assembly Switch InstallationTo install the switch To connect the motor cord to the motor Wiring ConnectionTo install the V-belt Jointer to StandBelt Stand Cover To install the stand coverFence to Jointer G0500/G1018HW Handwheel InstallationTo install the fence on the jointer unit To install the handwheels on the Model G0500/G1018HWTo assemble the knife setting gauge G1018 Table Lever InstallationKnife Setting Gauge To install the table levers on the Model G1018HWKnife Inspection Table AlignmentTo inspect the knife height Outfeed table check To adjust the infeed tableG1018 Table Stops To set the Model G1018 outfeed table stop boltTo set the Model G1018 infeed table stop bolt To install the cutterhead guard This operation is extremely important for operator safetyCutterhead Guard To check and adjust the 45˚ R fence stop To check and adjust the 90˚ fence stopFence Stops Test Run Plug InstallationTo check and adjust the 45˚L fence stop To install a plug on your power cordStock Inspection & Requirements OperationsSquaring Stock Illustration of surface planing effects Surface PlaningIllustration of edge jointing effects Edge JointingIllustration of bevel cutting effects Bevel CuttingIllustration of rabbet cutting effects A few sample joints Rabbet CuttingKnife Condition MaintenanceGeneral LubricationDate Approximate Hours Of Use Maintenance Performed To set the knives Service AdjustmentsAbout Service Setting KnivesTable gibs To adjust the table gibs Adjusting GibsTo adjust the V-belt tension Adjusting V-BeltsTo adjust the V-belt alignment Replacing V-BeltTo replace the V-belts Date Approximate Hours Of Use Service Performed Reference Info Symptom Possible Cause Corrective Action Troubleshooting GuideSee G0500/G1018/G1018HW Wiring Diagram Machine Data Sheet G0500 G0500 205 213 209 212 210 204211 202 208 201207 203 206 220 332 Base Cutterhead Model G1018 8 Jointer G1018 126 125 122 121 120 102 104 105 Table ADJ ROD 215 G1018 KNIVES, SET of Three Model G1018HW Jointer W/ Handwheels G1018HW 126 125 122 121 120 102 104 105 Rivet 2 X 5MM 202 205 211 203 204 210 213 209 212 208 207 201 206 214 G1018HW 328 PG1018323 Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog