DeWalt DW680-XE High-speed Steel Blades, Parking Foot Fig, Edge Chamfering Fig, Maintenance

Page 9

d. Simultaneously push the blade carrier (L) and the guide bar (M) into the gauge plate inside wall (O), making sure that the carbide blade (I) is held firmly against the gauge plate inside wall (O) and securely tighten the two hex screws (P).

3. To Reinstall Blade

a. Remove the adjusted blade carrier/guide bar assembly from the gauge plate (N)

and place the heel of the guide bar (M) into the groove on the drum (Q).

b. Place the drum cover (K) over the blade carrier/guide bar assembly. Loosely

3.To Reinstall Blade

a.Cautiously remove the adjusted guide bar/high speed steel blade assembly from the gauge plate (N) and place the heel of the guide bar (M) into the groove in the drum (Q).

b.Set the drum cover (K) over the adjusted guide bar/high speed steel blade assembly and securely tighten the three hex screws (J) to the drum.

4.Repeat procedure for the other blade.

screw the three hex screws (J) into the drum (Q) so that there is a small gap

between the drum and the blade carrier (L).

c. Slide the carbide blade between the drum (Q) and the blade carrier (L) so that

the rib on the blade carrier sets into the groove in the blade.

d. Center the carbide blade (I) under the blade carrier (L) making sure the blade is

clear of the tool housing on both sides.

e. Securely tighten the three hex screws (J) to the drum.

4. Repeat procedure for the other blade.

High-speed Steel Blades

1.

To Remove Blade from Planer

 

a. Loosen and remove the three hex head screws (J) with the 5 mm hex wrench

 

provided. Remove the drum cover (K) from the drum (Q).

 

b. Cautiously remove the guide bar/high speed steel blade assembly.

2.

To Adjust Blade Using Gauge Plate (provided with tool)

 

a. Place the guide bar/high speed steel blade assembly on the gauge plate (N)

 

with the cutting edge of the high speed steel blade flush against the gauge plate

Parking Foot (Fig. 11)

Your planer is equipped with a parking foot (S) that automatically lowers into place when the tool is lifted from the work surface. When planing, the parking foot raises as the tool is pushed forward. When the parking foot is lowered, the planer can set on the work surface without the blade touching.

Edge Chamfering (Fig. 12)

Your planer has three precision machined chamfering grooves (T) in the front shoe for planing along a corner of the wood (Fig. 12). The width of the grooves are 1.5 mm, 2 mm, and 2.5 mm. It’s a good idea to try a piece of scrap wood before doing finish work.

MAINTENANCE

FIG. 11

S

FIG. 12

inside wall (O). The heel of the guide bar (M) will overlap the end of the gauge

plate (N).

b. Loosen the two hex screws (P) with the 2.5 mm hex wrench provided.

c. Simultaneously push the high speed steel blade (R) and the guide bar (M)

into the gauge plate inside wall (O), making sure that the blade is held firmly

against the gauge plate inside wall (O) and securely tighten hex screws (P).

WARNING: To reduce the risk of injury,

T

turn unit off and disconnect tool from

 

power source before installing and removing accessories, before adjusting or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF position. An accidental start-up can cause injury.

7

Image 9
Contents DW680-XE Page Definitions Safety Guidelines Safety Instructions for Power ToolsGeneral Safety Rules Power Tool USE and Care Electrical SafetyService Extension CordsUNPLUGGED. Blades are Exposed and Extremely Sharp Additional Safety Instructions for PlanersIntroduction Switch FigComponents Fig OperationAdjusting Planing Depth Fig Planing , 3Rabbet Fence To Install Rabbet Fence To Make a Rabbet CutTo Change Blades , 8, 9 Reversible Carbide Blades High-speed Steel Blades MaintenanceParking Foot Fig Edge Chamfering FigGuarantee Cleaning FigThree Year Limited Warranty LubricationPage Copyright 2010 D Ewalt