|
| MINIMUM GAUGE FOR CORD SETS |
|
| ||||
For Cable length (m): | 7.5 | 15 | 25 | 30 | 45 | 60 | ||
Use Cable with minimum rating (Amperes) |
|
|
|
| ||||
Tool Amperes |
|
|
|
|
|
|
| |
0 | - 3.4 | 7.5 | 7.5 | 7.5 | 7.5 | 7.5 | 7.5 |
|
3.5 | - 5.0 | 7.5 | 7.5 | 7.5 | 7.5 | 10 | 15 |
|
5.1 | - 7.0 | 10 | 10 | 10 | 10 | 15 | 15 |
|
7.1 | - 12.0 | 15 | 15 | 15 | 15 | 20 | 20 |
|
12.1 | - 20.0 | 20 | 20 | 20 | 20 | 25 | – |
|
ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS
•To reduce the risk of injury, user must read and understand instruction manual before operating planer.
•Always wear eye protection and dust mask.
•Be sure the voltage agrees with specific data on the nameplate.
•Make certain that the switch is in the off position before connecting plug to a power source.
•Be sure to switch OFF immediately if tool is jammed in work.
•Be sure tool is set for correct depth before turning switch to ON.
•Be sure to use specified replacement parts only.
•Be sure tool is disconnected from power source when cleaning or making adjustments to
the tool.
•Be sure to maintain tool with care. Follow instructions for lubricating and changing accessories.
•Stay alert – never operate the unit when tired or under the influence of drugs, alcohol, or medication.
•Be sure to store tool in a clean dry place after disconnecting from power source.
•Do not use in dangerous environments. Do not use near flammable substances, in damp or wet locations, or expose to rain.
•Be sure that the blades are mounted as described in the instruction manual and check that all screws are firmly tightened before connecting unit to power source.
•Keep air vents unobstructed for proper motor cooling.
•DO NOT lay tool down on shoe when the blades are exposed. This can chip the blades.
•Keep side discharge chute unobstructed at all times.
•Never reach under the tool for any reason unless it is turned off and
UNPLUGGED. BLADES ARE EXPOSED AND EXTREMELY SHARP.
•Use this tool for working with wood and wood products only.
•Never operate without securely holding the front handle.
•Always operate planer with two hands.
•Planer blades are extremely sharp. Handle with great care.
•Clean out your tool often, especially after heavy use.
WARNING: ALWAYS wear approved protective safety equipment complying with the following standards:
•Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;
•Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;
•Respiratory protection: AS/NZS1716 Respiratory Protective Devices.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
3