Grizzly G0477 owner manual Mounting Planer/ Moulder on Stand, Dust Chute and Bag

Page 17

Mounting Planer/ Moulder on Stand

The Model G0477 is a very heavy machine. Get assistance when lift- ing the planer/moulder onto the stand. Failure to comply can result is seri- ous personal injury!

Components and Hardware Needed:

 

Hex Bolts M8-1.25 x 80

4

Flat Washers 8mm

8

Hex Nuts M8-1.25

4

To mount the planer/moulder to the stand:

1.Position the assembled stand so that it is on a flat, level surface and is clear of nearby equipment or other obstructions.

2.With the help of an assistant, lift the planer/ moulder onto the stand.

3.Align the mounting holes in the base cast- ing of the planer/moulder with the mounting holes in the stand, as shown in Figure 8.

Mounting Hole

Figure 8. Mounting holes in base casting.

4.Fasten the planer/moulder to the stand using the M8-1.25 x 80 hex bolts, flat washers and hex nuts.

Model G0477 15" Planer/Moulder

Dust Chute and Bag

DO NOT operate the Model G0477 without the dust collection bag installed. This plan- er/moulder creates substantial amounts of wood dust while operating. Failure to use the dust collection bag can result in short and long-term respiratory illness.

Components and Hardware Needed:

Qty

Dust Chute

1

Button Head Cap Screw M6-1 x 25

1

Dust Collection Bag

1

Bag Clamp

1

Dust Chute Adapter

1

Cap Screw M6-1 x 25

1

To install the dust chute and bag:

 

1.Fasten the dust chute on the fan cover using the button head cap screw.

2.Fit the dust chute adapter over the dust chute and fasten in place using the cap screw.

3.Slip the bag clamp over the neck of the bag, and fit the bag opening onto the dust chute adapter.

4.Close the clamp to fasten the bag onto the dust chute adapter.

5.Give the bag a slight tug to ensure it is secured tightly.

Note: If the clamp seems to be too loose or too tight when the clamp is engaged, it can be adjusted by rotating the clamping handle. Rotate the clamping handle clockwise to tighten the clamp or counterclockwise to loosen the clamp.

-15-

Image 17
Contents Model G0477 PLANER/MOULDER Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Data Sheet Other Identification ON/OFF SwitchSafety Instructions for Machinery SafetyChILdREN & BYsTANdERs. Keep­children­and­ Maintain Power CORds. When­ disconnectAdditional Safety for Planer/Moulders Full-Load Current Rating at 12A Phase110V/120V 60 Hz50 ft Minimum Gauge Size 14 AWGItems Needed for Set Up SET UPUnpacking Description QtyComponents and Hardware not shown InventoryInventory Figure Qty Site Considerations Clean UpTo assemble the stand Stand AssemblyComponents and Hardware Needed Qty Mounting Planer/ Moulder on Stand To install the dust chute and bagDust Chute and Bag To mount the planer/moulder to the standCrank Handle To install the crank handle FigureTest Run To test run the machineOperations Operation Safety Safety Switch KeyBasic Operation Basic steps of operating the planer/ moulder are as followsFeed Speed Operation TipsPreset Thickness Settings Headstock Height AdjustmentTo use the preset depth gauge Figure To change the headstock height manuallyTo adjust the infeed/outfeed roller height Roller Height AdjustmentTools Needed Qty Moulding KnivesEdge Moulding Setting Up Moulding Fence GuideAdjusting Moulding Guide Fence Wing Bolt Model G0477 15 Planer/Moulder Moulding KnivesMaintenance Troubleshooting Guide SERVicEPlaner/Moulder Operations To change the planing knives Changing Planing KnivesChain Tension and Headstock Leveling Changing BeltsTo change the drive and fan belts Tools Needed Qty Hex Wrench 4mmTo replace motor brushes Changing Motor BrushesTools Needed Qty Flat Head Screwdriver Electrical Components Model G0477 Wiring DiagramG0477 Body Breakdown G0477 Table and Base G0477 Gearbox Breakdown G0477 Stand Breakdown G0477 Labels Description Parts ListFAN Cover Chain Protector PK48M Page Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns
Related manuals
Manual 48 pages 3.5 Kb