Grizzly G0477 owner manual Changing Belts, Chain Tension and Headstock Leveling

Page 31

Changing Belts

 

Tools Needed:

Qty

Hex Wrench 4mm

1

Hex Wrench 5mm

1

The Model G0477 features two ribbed belts, shown in Figure 26, that are generally good for the life of the machine. However, there are some instances where these belts must be replaced.

Motor Tension Cap Screw

Drive Belt

Fan Belt

 

Figure 26. Drive and fan belts.

To change the drive and fan belts:

1.DISCONNECT THE MACHINE FROM THE POWER SOURCE!

2.Unscrew and remove the cap screw that holds the crank handle in place, and remove the crank handle.

3.Remove the four set screws that hold the housing caps in place.

4.Remove the right housing cap, feed rollers, preset depth gauge knob, and right housing cover.

5.Roll the fan belt off the pulleys.

6.Loosen the motor tension cap screw indi- cated in Figure 26 to lower the motor and to put slack on the drive belt.

7.Roll the drive belt off the cutterhead pulley.

Model G0477 15" Planer/Moulder

8.Lift the drive belt off the motor pulley and slide it through the space between the pulley and the headstock casting to free it from the machine.

9.Repeat Steps 5, 7 and 8 in reverse order to install new fan and drive belts.

10.Once both belts have been installed, have an assistant lift the motor slightly to place tension on the drive belt, and tighten the cap screw loosened in Step 6. Both belts should now have a displacement or "give" of around 14" on each side.

Chain Tension and Headstock Leveling

Tools Needed:

Qty

Hex Wrench 4mm.

............................................. 1

If the headstock slips out of alignment with the table, the planer/moulder will produce an uneven cut. Often this is due to the chain losing tension over time. Follow these steps to correct head- stock misalignment and to correct chain slack.

To correct a misaligned headstock:

1.DISCONNECT THE PLANER FROM THE POWER SOURCE!

2.Place even-sized shims under each corner of the headstock and lower it until the head- stock rests on at least one of the shims.

3.If there is a gap between the headstock and any shim(s), proceed to the next step. If there is no gap, the headstock needs no adjustment.

4.Loosen, but do not remove, the two cap screws shown in Figure 27 and slide the idler bracket so the chain loosens slightly.

-29-

Image 31
Contents Model G0477 PLANER/MOULDER Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Data Sheet Other Identification ON/OFF SwitchSafety Instructions for Machinery SafetyChILdREN & BYsTANdERs. Keep­children­and­ Maintain Power CORds. When­ disconnectAdditional Safety for Planer/Moulders 60 Hz PhaseFull-Load Current Rating at 12A 110V/120V50 ft Minimum Gauge Size 14 AWGDescription Qty SET UPItems Needed for Set Up UnpackingInventory Figure Qty InventoryComponents and Hardware not shown Site Considerations Clean UpComponents and Hardware Needed Qty Stand AssemblyTo assemble the stand To mount the planer/moulder to the stand To install the dust chute and bagMounting Planer/ Moulder on Stand Dust Chute and BagTo test run the machine To install the crank handle FigureCrank Handle Test RunBasic steps of operating the planer/ moulder are as follows Operation Safety Safety Switch KeyOperations Basic OperationFeed Speed Operation TipsTo change the headstock height manually Headstock Height AdjustmentPreset Thickness Settings To use the preset depth gauge FigureTo adjust the infeed/outfeed roller height Roller Height AdjustmentTools Needed Qty Moulding KnivesAdjusting Moulding Guide Fence Setting Up Moulding Fence GuideEdge Moulding Wing Bolt Model G0477 15 Planer/Moulder Moulding KnivesMaintenance Troubleshooting Guide SERVicEPlaner/Moulder Operations To change the planing knives Changing Planing KnivesTools Needed Qty Hex Wrench 4mm Changing BeltsChain Tension and Headstock Leveling To change the drive and fan beltsTools Needed Qty Flat Head Screwdriver Changing Motor BrushesTo replace motor brushes Electrical Components Model G0477 Wiring DiagramG0477 Body Breakdown G0477 Table and Base G0477 Gearbox Breakdown G0477 Stand Breakdown G0477 Labels Description Parts ListFAN Cover Chain Protector PK48M Page Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns
Related manuals
Manual 48 pages 3.5 Kb