Grizzly G0477 owner manual Moulding Knives, Tools Needed Qty

Page 23

Moulding Knives

Tools Needed:

Qty

Wrench 8mm

1

The G0477 has two moulding knife slots. Each slot can accommodate two different moulding knives at the same time. However, both moulding knife slots must be set up identically for a suc- cessful moulding operation. The planing knives do not need to be removed when moulding.

To install/change the moulding knives on your planer/moulder:

1.UNPLUG THE PLANER/MOULDER FROM THE POWER SOURCE!

2.Push the cutterhead lock down, and rotate the cutterhead until the moulding knife slot is visible, as shown in Figure 18, then release the cutterhead lock and slightly rotate the cutterhead in either direction until it locks.

6.Slide the moulding knife up against the set- ting block.

7.Balance the opposite end of the gib using the provided spacers, as shown in Figure 19. Always ensure that the spacers used are the same width as the moulding knife.

Moulding

Spacers

Knife

 

Setting Block

Gib

 

Figure 19. Moulding knife installation.

8.Tighten the gib bolts in the order indicated in Figure 20.

Setting Block

Figure 18. Moulding knife slot.

4.Ensure the moulding knife slot is clean and clear of dirt, dust and other debris.

5.With the gib bolts already inserted into the gib, place the gib in the moulding knife slot.

Model G0477 15" Planer/Moulder

5

 

3

 

1

 

2

 

4

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 20. Gib bolt tightening sequence

(moulding knives).

9.Repeat Steps 2–8to install one or more addi- tional moulding knives.

-21-

Image 23
Contents Model G0477 PLANER/MOULDER Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Data Sheet Other Identification ON/OFF SwitchSafety Instructions for Machinery SafetyChILdREN & BYsTANdERs. Keep­children­and­ Maintain Power CORds. When­ disconnectAdditional Safety for Planer/Moulders 60 Hz PhaseFull-Load Current Rating at 12A 110V/120V50 ft Minimum Gauge Size 14 AWGDescription Qty SET UPItems Needed for Set Up UnpackingComponents and Hardware not shown InventoryInventory Figure Qty Site Considerations Clean UpTo assemble the stand Stand AssemblyComponents and Hardware Needed Qty To mount the planer/moulder to the stand To install the dust chute and bagMounting Planer/ Moulder on Stand Dust Chute and BagTo test run the machine To install the crank handle FigureCrank Handle Test RunBasic steps of operating the planer/ moulder are as follows Operation Safety Safety Switch KeyOperations Basic OperationFeed Speed Operation TipsTo change the headstock height manually Headstock Height AdjustmentPreset Thickness Settings To use the preset depth gauge FigureTo adjust the infeed/outfeed roller height Roller Height AdjustmentTools Needed Qty Moulding KnivesEdge Moulding Setting Up Moulding Fence GuideAdjusting Moulding Guide Fence Wing Bolt Model G0477 15 Planer/Moulder Moulding KnivesMaintenance Troubleshooting Guide SERVicEPlaner/Moulder Operations To change the planing knives Changing Planing KnivesTools Needed Qty Hex Wrench 4mm Changing BeltsChain Tension and Headstock Leveling To change the drive and fan beltsTo replace motor brushes Changing Motor BrushesTools Needed Qty Flat Head Screwdriver Electrical Components Model G0477 Wiring DiagramG0477 Body Breakdown G0477 Table and Base G0477 Gearbox Breakdown G0477 Stand Breakdown G0477 Labels Description Parts ListFAN Cover Chain Protector PK48M Page Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns
Related manuals
Manual 48 pages 3.5 Kb