Miller Electric Maxstar 200 STR manual California Proposition 65 Warnings

Page 9

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before re- connecting input power.

READ INSTRUCTIONS.

DRead Owner’s Manual before using or servic- ing unit.

DUse only genuine Miller/Hobart replacement parts.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-4. California Proposition 65 Warnings

YWelding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

YBattery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

For Gasoline Engines:

YEngine exhaust contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

For Diesel Engines:

YDiesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

OM-2233 Page 3

Page 8 Page 10
Image 9
Page 8 Page 10
Contents OM-2233 203 409Q ProcessesDescription From Miller to You Table of Contents − Parts List Directives StandardsDecstat6/05 Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Definitions CE Models Electric shock from welding electrode or wiring can killWeee Label For Products Sold Within The EU 60 sFalling equipment can cause injury and damage to unit Manufacturer’s Rating Label Symbols And DefinitionsSpecifications − InstallationVolt-Ampere Curves 5 V a C In p u tTh e r In p u t V o lt a g e s Minutes Welding Duty Cycle And OverheatingOverheating MinutesSelecting a Location Dimensions And WeightSection Location And AirflowRemote 14 Receptacle Information Weld Output Terminals And Selecting Cable SizesTurn off power before mak- ing connections Stick Dcep Direct Current Electrode Positive Connections Electrical Service GuideInput Voltage Input Amperes At Rated OutputConnecting Three-Phase Input Power Connecting Input PowerFor Three-Phase Operation = GND/PE Earth GroundConnecting Single-Phase Input Power − Operation ControlsNon CE Units For CE Units Process Control Lift-ArcStart ProcedureLift-Arc Start ApplicationAmperage Control Stick Start Procedure − Scratch Start TechniqueDIG Control MinRoutine Maintenance − Maintenance and TroubleshootingBlowing Out Inside Of Unit MonthsTroubleshooting Help Aids Output LED High Temperature LEDHelp 8 Display Trouble Remedy TroubleshootingShield weld zone from drafts Check and tighten all gas fittings see SectionCircuit Diagram − Electrical DiagramsUp to Amperage Range Gas Type PolarityPositioning The Torch − Guidelines for Gtaw TIG WeldingPositioning Torch Tungsten For Various Weld Joints Torch Movement During WeldingTungsten Without Filler Rod Tungsten With Filler RodStick Welding Procedure Weld current starts when electrode touches work- piece− Stick Welding Smaw Guidelines Electrode and Amperage Selection Chart Striking an Arc − Scratch Start TechniqueStriking an Arc − Tapping Technique Good Weld Bead Characteristics Poor Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work AngleElectrode Movement During Welding Conditions That Affect Weld Bead ShapeLap Joint Butt JointsTee Joint 16 in 30 1.6 mm Tack WeldsTroubleshooting − Excessive Spatter Troubleshooting − PorosityWeld Test Possible Causes Corrective ActionsTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Excessive Penetration Troubleshooting − Burn-Through Troubleshooting − Waviness Of BeadTroubleshooting − Distortion − Parts List 2734 401 400402 614615 600 PC2 602 400 601 603 605 Panel, Front w/Components -1ItemPanel, Rear w/Components Magnetics Assembly w/Components 1Item Windtunnel w/Components -1Item Windtunnel w/Components604 600 601 602 604Base Assembly Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Maxstar 200 STR specifications

The Miller Electric Maxstar 200 STR is a versatile and compact welding power source designed for a range of applications, making it an ideal choice for both professional welders and hobbyists. Known for its reliability and exceptional performance, the Maxstar 200 STR is capable of delivering high-quality results in various welding processes, including Stick (SMAW) and TIG (GTAW) welding.

One of the standout features of the Maxstar 200 STR is its inverter technology, which allows for efficient energy use and a lightweight, portable design. Weighing in at just 51 pounds, it is easy to transport, making it perfect for fieldwork or remote projects. The unit operates on both 120V and 240V input power, providing versatility for different environments and applications. This adaptability ensures that welders can work effectively in various settings, whether in a shop or on a construction site.

Another significant characteristic of the Maxstar 200 STR is its precise arc control. The machine offers adjustable AC frequency, allowing users to fine-tune the arc characteristics for different materials and thicknesses. This level of control is particularly beneficial when working with aluminum, as it helps reduce heat input and minimize warping. The Maxstar also features a pulsing function, which can enhance the weld pool control and improve penetration, making it easier to achieve clean and consistent welds.

The Maxstar 200 STR boasts a robust duty cycle of 60% at 200A, ensuring that it can handle demanding jobs without overheating. Additionally, the unit is equipped with an advanced cooling system, which helps maintain optimal performance during extended use. Safety features, including overload protection and an enclosed design that reduces the risk of contamination, further enhance the machine's reliability.

Moreover, the Maxstar 200 STR supports a range of accessories, including a remote foot control, which allows for added flexibility during TIG welding operations. This feature is particularly useful for precise control over the welding current, enabling welders to make adjustments on the fly without having to stop and manually change settings.

In summary, the Miller Electric Maxstar 200 STR stands out in the welding industry for its combination of portability, advanced technology, and high performance. With its inverter design, precise arc control, and robust duty cycle, it is an ideal solution for professionals seeking efficiency and quality in their welding projects, whether they are working on industrial applications or artistic endeavors.
Top Page Image Contents