Miller Electric Maxstar 200 STR manual Turn off power before mak- ing connections

Page 23

4-7. TIG Lift-Arc DCEN (Direct Current Electrode Negative) Connections

YTurn off power before mak- ing connections.

1Positive (+) Weld Output Terminal

4Connect work lead to positive weld output terminal.

2 Negative (−) Weld Output Terminal

Connect TIG torch to negative weld output terminal.

3 Gas Cylinder

4 Cylinder Valve

Open valve slightly so gas flow blows dirt from valve. Close valve. 5 Regulator/Flowmeter

6 Flow Adjust

Typical flow rate is 15 cubic feet per hour (7.1 liters per minute).

Connect torch gas hose to regula- tor/flowmeter.

7 Gas Valve

Valve controls gas preflow and postflow. Open valve on torch just before welding.

Tools Needed:

11/16 in, 1-1/8 in, (21 mm)

Ref. 802 888-A

OM-2233 Page 17

Image 23

Contents Description OM-2233 203 409QProcesses From Miller to You Table of Contents − Parts List Decstat6/05 DirectivesStandards Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Definitions CE Models Electric shock from welding electrode or wiring can killFalling equipment can cause injury and damage to unit Weee Label For Products Sold Within The EU60 s Manufacturer’s Rating Label Symbols And DefinitionsSpecifications − InstallationTh e r In p u t V o lt a g e s Volt-Ampere Curves5 V a C In p u t Minutes Duty Cycle And OverheatingMinutes Welding OverheatingLocation And Airflow Dimensions And WeightSelecting a Location SectionRemote 14 Receptacle Information Weld Output Terminals And Selecting Cable SizesTurn off power before mak- ing connections Input Amperes At Rated Output Electrical Service GuideStick Dcep Direct Current Electrode Positive Connections Input Voltage= GND/PE Earth Ground Connecting Input PowerConnecting Three-Phase Input Power For Three-Phase OperationConnecting Single-Phase Input Power Non CE Units − OperationControls For CE Units Application Lift-ArcStart ProcedureProcess Control Lift-Arc StartMin Stick Start Procedure − Scratch Start TechniqueAmperage Control DIG ControlMonths − Maintenance and TroubleshootingRoutine Maintenance Blowing Out Inside Of UnitHelp 8 Display Troubleshooting Help AidsOutput LED High Temperature LED Check and tighten all gas fittings see Section TroubleshootingTrouble Remedy Shield weld zone from draftsCircuit Diagram − Electrical DiagramsUp to Amperage Range Gas Type PolarityPositioning The Torch − Guidelines for Gtaw TIG WeldingTungsten With Filler Rod Torch Movement During WeldingPositioning Torch Tungsten For Various Weld Joints Tungsten Without Filler Rod− Stick Welding Smaw Guidelines Stick Welding ProcedureWeld current starts when electrode touches work- piece Striking an Arc − Tapping Technique Electrode and Amperage Selection ChartStriking an Arc − Scratch Start Technique 10-30 9090 End View of Work Angle Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Positioning Electrode HolderElectrode Movement During Welding Conditions That Affect Weld Bead Shape16 in 30 1.6 mm Tack Welds Butt JointsLap Joint Tee JointPossible Causes Corrective Actions Troubleshooting − PorosityTroubleshooting − Excessive Spatter Weld TestTroubleshooting − Excessive Penetration Troubleshooting − Incomplete FusionTroubleshooting − Lack Of Penetration Troubleshooting − Distortion Troubleshooting − Burn-ThroughTroubleshooting − Waviness Of Bead 615 600 − Parts List2734 401 400402 614 PC2 602 400 601 603 605 Panel, Front w/Components -1ItemPanel, Rear w/Components Magnetics Assembly w/Components 1Item Windtunnel w/Components -1Item Windtunnel w/Components604 600 601 602 604Base Assembly Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact

Maxstar 200 STR specifications

The Miller Electric Maxstar 200 STR is a versatile and compact welding power source designed for a range of applications, making it an ideal choice for both professional welders and hobbyists. Known for its reliability and exceptional performance, the Maxstar 200 STR is capable of delivering high-quality results in various welding processes, including Stick (SMAW) and TIG (GTAW) welding.

One of the standout features of the Maxstar 200 STR is its inverter technology, which allows for efficient energy use and a lightweight, portable design. Weighing in at just 51 pounds, it is easy to transport, making it perfect for fieldwork or remote projects. The unit operates on both 120V and 240V input power, providing versatility for different environments and applications. This adaptability ensures that welders can work effectively in various settings, whether in a shop or on a construction site.

Another significant characteristic of the Maxstar 200 STR is its precise arc control. The machine offers adjustable AC frequency, allowing users to fine-tune the arc characteristics for different materials and thicknesses. This level of control is particularly beneficial when working with aluminum, as it helps reduce heat input and minimize warping. The Maxstar also features a pulsing function, which can enhance the weld pool control and improve penetration, making it easier to achieve clean and consistent welds.

The Maxstar 200 STR boasts a robust duty cycle of 60% at 200A, ensuring that it can handle demanding jobs without overheating. Additionally, the unit is equipped with an advanced cooling system, which helps maintain optimal performance during extended use. Safety features, including overload protection and an enclosed design that reduces the risk of contamination, further enhance the machine's reliability.

Moreover, the Maxstar 200 STR supports a range of accessories, including a remote foot control, which allows for added flexibility during TIG welding operations. This feature is particularly useful for precise control over the welding current, enabling welders to make adjustments on the fly without having to stop and manually change settings.

In summary, the Miller Electric Maxstar 200 STR stands out in the welding industry for its combination of portability, advanced technology, and high performance. With its inverter design, precise arc control, and robust duty cycle, it is an ideal solution for professionals seeking efficiency and quality in their welding projects, whether they are working on industrial applications or artistic endeavors.