Stanley Black & Decker BR87 user manual Charging the Accumulator, Accumulator Testing Procedure

Page 14

CHARGING THE ACCUMULATOR

ACCUMULATOR TESTING

PROCEDURE

To check or charge the accumulator the following equip- ment is required:

31254 Charge Kit: which includes the following.

•Accumulator Tester (Part Number 02835)

•Charging Assembly (P/N 15304)

(P/N 15304 includes a liquid filled gauge with snub valve, hose and fittings.)

•NITROGEN bottle with an 1000 psi/70 bar minimum charge. (Not included in 31254 Charge Kit.)

CAUTION

This assembly contains nitrogen under pressure

1.Remove the valve cap assembly from the breaker.

2.Remove the protective cap and loosen the 5/8-inch hex locking nut on the tool charging valve 1-1/2 turns.

3.Holding the chuck end of Accumulator Tester (P/N 02835) turn the gauge fully counterclockwise to en- sure that the stem inside the chuck is completely retracted.

4.Thread the tester onto the accumulator charg- ing valve. Do not advance the gauge-end into the chuck-end. Turn as a unit. Seat the chuck on the accumulator charging valve and hand tighten only.

5.Advance the valve stem of the tester by turning the gauge-end clockwise until a pressure is read on the gauge (charge pressure should be 700-900 psi/48- 62 bar).

6.If pressure is OK unscrew the gauge-end from the chuck to retract the stem, then unscrew the entire tester assembly from the accumulator charging valve. If pressure is low, charge the accumulator as described in the following paragraph.

7.Tighten the 5/8-inch hex locking nut on the tool charging valve. Be careful not to overtighten. Install the protective cap and valve cap assembly.

ACCUMULATOR CHARGING

1.Perform steps 1 through 4 of the accumulator test- ing procedure above.

2.Connect the chuck of the charging assembly to the charging valve on the accumulator tester or, if pre- ferred, remove the tester from the charging valve and connect the charging assembly chuck directly to the charging valve.

3.Adjust the regulator to the charging pressure of 800 psi/55 bar.

NOTE:

It may be necessary to set the gauge at 850-900 psi/59-62 bar to overcome any pressure drop through the charging system.

4.Open the valve on the charging assembly hose.

5.When the accumulator is fully charged close the valve on the charging assembly hose and remove the charging assembly chuck from the accumulator tester or tool charging valve.

If the accumulator tester has been used, be sure to turn the gauge-end fully counterclockwise before re- moving the tester from the charging valve of the tool.

6.Tighten the 5/8-inch hex locking nut on the tool charging valve and replace the protective cap.

7.Replace the valve cap assembly.

GENERAL SERVICE NOTES

1.If the breaker is repainted after servicing, be sure to mask off the vent in the valve cap assembly. Do not allow paint to enter the IN and OUT ports or the bore of the foot assembly.

2.If the handle grips need to be replaced.

a.Remove the old grips and clean the handle.

b.Wash the new grips and the handle clean and dry, simply push or drive the grips on. DO NOT lubricate the parts. The grips will not be secure on the handle if any grease or oil is used.

14 ► BR87 User Manual

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Hydraulic Breaker Declaration of Conformity Weisbeck, AndyTable of Contents Safety Symbols Local Safety RegulationsSafety Precautions Safety Precautions Tool Stickers & Tags N G E RHose Safety Tags Hose TypesHose Recommendations Tool to Hydraulic Circuit Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsOperation PRE-OPERATION ProceduresOperation Procedures Cold Weather OperationTool Protection & Care Troubleshooting Problem Cause RemedyCharging the Accumulator Accumulator Testing ProcedureGeneral Service Notes Accumulator ChargingUnderwater Model Preventative Maintenance Specifications BR87 Sound and Vibration DeclarationTest Equipment AccessoriesService Tools BR87 Parts Illustration BR87 Parts Illustration BR87 Parts List Part Qty DescriptionGPM Underwater Tools Depth GuidelineUnderwater Models only

BR87 specifications

Stanley Black & Decker BR87 is a robust and innovative tool that is designed to meet the demands of both professional contractors and DIY enthusiasts. This powerful tool combines cutting-edge technology with a user-friendly design, making it an essential addition to any toolbox.

One of the standout features of the BR87 is its high-performance motor. Designed to deliver a strong output, this motor ensures efficient operation across a variety of applications. Whether users are drilling into wood, metal, or masonry, the BR87 adapts to different materials effortlessly. Furthermore, the tool's variable speed control allows users to adjust the speed according to the task, providing added precision and versatility.

Another key characteristic of the BR87 is its ergonomic design. The tool is equipped with a comfortable grip that reduces hand fatigue during prolonged use. This is particularly beneficial for professionals who may be using the tool for extended periods on job sites. Additionally, its lightweight design makes it easy to maneuver, further enhancing user comfort.

The BR87 is also packed with advanced safety features. It includes a built-in overload protection system that prevents damage to the motor in case of excessive strain. This feature not only prolongs the lifespan of the tool but also ensures user safety. The design adheres to the highest industry standards, making it a reliable choice for construction and renovation projects.

In terms of technology, the BR87 utilizes a brushless motor, which enhances its efficiency and runtime. Unlike traditional motors, brushless designs produce less heat and require less maintenance, resulting in longer operational life. This technology also contributes to reduced noise levels, making it pleasant to use in residential areas.

Additionally, the BR87 is compatible with a range of accessories and attachments, allowing users to customize their tool for specific tasks. From drill bits to chisels, the versatility of the BR87 makes it suitable for a wide array of projects.

In summary, the Stanley Black & Decker BR87 is a powerful, versatile, and user-friendly tool that combines advanced features with an ergonomic design. With its high-performance motor, brushless technology, and strong safety mechanisms, the BR87 stands out in its category. Whether for professional use or home improvement tasks, the BR87 delivers reliability and efficiency that users can depend on.
Top Page Image Contents