Miller Electric OM-230 Connecting XR Aluma-Pro, XR Edge, XR-A Gun, Or XR-A Python, 32 in 2.4 mm

Page 19

.A complete Parts List is available at www.MillerWelds.com

4-7. Connecting XR Aluma-Pro, XR Edge, XR-A Gun, Or XR-A Python

3/32 in (2.4 mm)

2 3

.XR Edge guns prior to serial no. LE079101 require an adapter cord (part no. 195 498).

1Gun End

2Gun Liner

3Wire Outlet Guide

Trim excess liner from end of gun so no more than 3/32 in (2.4 mm) of liner extends past wire outlet guide.

4 Gun Securing Knob

Loosen securing knob. Insert gun end through opening until it bottoms against drive assembly (make sure gun end does not touch drive rolls). Tighten knob.

Be sure to change drive rolls to the

4proper size and type.

5 Gun Trigger Plug

Insert plug into receptacle, and tighten threaded collar.

. If Aluma-Pro push/pull gun has a listed SUP value, set the power source to match the SUP value (see Section 5-5).

. Be sure to trim liner to proper extension.

Ref. 804 910-A / 804 936-A

OM-230 693 Page 15

Image 19

Contents File MIG Gmaw OM-230 693CProcesses DescriptionFrom Miller to You Table of Contents − MIG Welding Gmaw Guidelines − Parts ListTypical MIG Process Connections HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLOLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-230 693 Specifications Symbols And DefinitionsVolt-Ampere Curves Welding Power Source Duty Cycle And OverheatingOverheating Installing Work Cable And Clamp Connecting To Weld Output TerminalsConnecting Spoolmatic 15A Or 30A Gun Gun End Gun Liner Wire Outlet Guide Connecting XR Aluma-Pro, XR Edge, XR-A Gun, Or XR-A Python32 in 2.4 mm 11/16 Setting Gun Polarity For Wire TypeInstalling Gas Supply Polarity Changeover Label InformationPositioning Jumper Links Installing Wire Spool And Adjusting Hub Tension127 206 Electrical Service GuideInput Voltage 200 230 460 57518 in 457 mm of space for airflow =GND/PE Earth Ground Selecting a Location And Connecting Input PowerL2L1 230 VAC Remove gun nozzle and contact tip Threading Welding WirePressure ScaleOM-230 693 Weld Parameters 226 650-B Controls − OperationRun−in Wire Feed Speed Settings JOG ModeTrigger and pull the trigger again momentarily one second Welding Status Voltmeter And Wire Feed Speed Meter OperationJog Mode Power Up StatusTimers Set Up Push Motor Torque SUP Or Reset rES Changing Drive Roll and Wire Inlet Guide Routine MaintenanceUnit Overload View is from top of drive rolls Aligning Drive Rolls and Wire GuideTurn Off power Assembly openTroubleshooting Trouble Remedy OM-230 693 − Electrical Diagram 229 485-A Typical MIG Process Connections − MIG Welding Gmaw GuidelinesSelect Voltage Typical MIG Process Control SettingsWire Size Amperage Range Select Wire Size Recommendation Wire SpeedSide View Of Gun Angle Holding And Positioning Welding GunSlow Normal Conditions That Affect Weld Bead ShapePush Perpendicular Drag Short Normal LongGood Weld Bead Characteristics Poor Weld Bead CharacteristicsGun Movement During Welding Possible Causes Corrective Actions Troubleshooting − Excessive SpatterTroubleshooting − Porosity Troubleshooting − Excessive PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Burn-Through Troubleshooting − Distortion Troubleshooting − Waviness Of BeadWeld bead Common MIG Shielding Gases Troubleshooting Guide For Semiautomatic Welding EquipmentApplication Drive rolls if necessary Welding arc not stable Wire slipping in drive rollsReadjust welding parameters Welding power source0.9 mm 204 Drive Roll And Wire Guide Kits087 Grooved 056Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact