Miller Electric OM-2241 manual Principales normes de sécurité

Page 12

2-4. Principales normes de sécurité

Safety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1, de l’American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126 (téléphone :(305) 443−9353, site Web : www .aws.org).

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers and Piping, norme American Welding Society AWS F4.1, de l’American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126 (téléphone : (305) 443−9353, site Web : www.aws.org).

National Electrical Code, norme NFPA 70, de la National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (téléphone : (617) 770−3000, sites Web : www.nfpa.org et www.sparky.org).

Safe Handling of Compressed Gases in Cylinders, brochure CGA P−1, de la Compressed Gas Association, 1735 Jefferson Davis Highway, Suite 1004, Arlington, VA 22202−4102 (téléphone : (703) 412−0900, site Web : www.cganet.com).

Code for Safety in Welding and Cutting, norme CSA W117.2, de la Ca- nadian Standards Association, Standards Sales, 178 boulevard

Rexdale, Rexdale (Ontario) Canada M9W 1R3 (téléphone : (800)

463−6727 ou à T oronto : (416) 747−4044, site Web : www .csa−interna- tional.org).

Practice For Occupational And Educational Eye And Face Protection, norme ANSI Z87.1, de l’American National Standards Institute, 11 West 42nd Street, New York, NY 10036−8002 (téléphone : (212) 642−4900, site Web : www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, norme NFPA 51B, de la National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (télé- phone : (617) 770−3000, site Web : www.nfpa.org et www.sparky.org).

OSHA, Occupational Safety and Health Standards for General Indus- try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, de l’U.S. Government Printing Office, Super- intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a 10 bureaux régionaux − Téléphone pour la Région 5, Chicago : (312) 353−2220, site Web : www.osha.gov).

2-5. Information sur les champs électromagnétiques

Donnéessur le soudage électrique et les effets des champs magnéti- ques basse fréquence sur l’organisme

En parcourant les câbles de soudage, le courant crée des champs élec- tromagnétiques. Les effets potentiels de tels champs restent préoccupants.Cependant, après avoir examiné plus de 500 études qui ont été faites pendant une période de recherche de 17 ans, un comité de spécialistes du National Research Council a conclu : « L ’accumula- tion de preuves n’a pas démontré que l’exposition aux champs magnétiques et aux champs électriques à haute fréquence constitue un risque pour la santé humaine ». Toutefois, les études et l’examen des preuves se poursuivent. En attendant les conclusions finales de la re- cherche, il serait souhaitable de réduire l’exposition aux champs électromagnétiquespendant le soudage ou le coupage.

Afin de réduire les champs électromagnétiquesen milieu de travail, res- pecter les consignes suivantes :

1.Garder les câbles ensemble en les torsadant ou en les fixant avec du ruban adhésif.

2.Mettre tous les câbles du côté opposé à l’opérateur.

3.Ne pas s’enrouler les câbles autour du corps.

4.Garder le poste de soudage et les câbles le plus loin possible de soi.

5.Placer la pince de masse le plus près possible de la zone de soudage.

Consignes relatives aux stimulateurs cardiaques :

Les personnes qui portent un stimulateur cardiaque doivent avant tout consulter leur médecin. Si ce dernier les déclare aptes, il leur est recom- mandé de respecter les consignes ci-dessus.

OM-2241 Page 8

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OM-2241 ProcessesDescription From Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers Identifie un message de sécurité particulier − Consignes DE Sécurité − À Lire Avant UtilisationLE Soudage peut causer un incen- die ou une explosion LES Particules Projetées peu- vent blesser les yeuxLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Bruit peut affecter l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut Faire LES Pièces Mobiles peuvent cau- ser des blessuresPrincipales normes de sécurité Information sur les champs électromagnétiquesConsignes relatives aux stimulateurs cardiaques Specifications Duty Cycle And Overheating230 OverheatingVolt-Ampere Curves Be careful when placing or moving unit over uneven surfaces Selecting a LocationTipping Movement Location And AirflowDimensions And Weights DimensionsWeight VAC Receptacle And Circuit BreakersWeld Output Terminals And Selecting Cable Sizes 10 − 60% 60 − 100%Duty Cycle Turn off power before con- necting to receptacle Remote 14 Receptacle RC8Remote 14 Receptacle RC8 Information InformationElectrical Service Guide Placing Jumper LinksInput Voltage Input Amperes At Rated OutputConnecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Con- nections Routine Maintenance Disconnect input power before maintaining MonthsControls Disconnect input power be- fore opening rear access door Fuse F1Short Circuit Shutdown Troubleshooting Table Trouble Remedy− Electrical Diagram OM-2241 − Parts List 1Main Assembly 2Panel, Front w/Components -1Item Rectifier, Si Diode SR1 1754Panel, Rear w/Components -1Item Service SupportOwner’s Record Miller Electric Mfg. Co

OM-2241 specifications

The Miller Electric OM-2241 is a versatile and innovative welding machine designed for both professional and industrial use. This power source is known for its durability, performance, and user-friendly features, making it a preferred choice for welders across various sectors.

One of the main features of the OM-2241 is its advanced multi-process capabilities. This welding machine can seamlessly switch between MIG, TIG, stick, and flux-cored welding, allowing users to tackle a wide array of projects with ease. This flexibility makes it suitable for various applications, from maintenance and repair to fabrication and construction.

The OM-2241 is equipped with Miller's Auto-Set technology, which simplifies the setup process. This feature automatically adjusts the machine's settings based on the material thickness and type, enabling users to achieve optimal weld quality without the need for extensive calibration. This is particularly beneficial for both novice and experienced welders, as it reduces the learning curve and increases efficiency.

Another notable characteristic of the OM-2241 is its lightweight and portable design. Weighing significantly less than traditional welding machines, it allows for easy transportation, making it an excellent option for on-site work. The machine also boasts an ergonomic handle and intuitive control panel, enhancing user comfort and accessibility during operation.

In terms of performance, the OM-2241 provides a stable arc and reduced spatter, resulting in clean and professional-looking welds. Its built-in digital meter provides real-time feedback on voltage and amperage, allowing welders to monitor their performance closely and make adjustments as needed.

The Miller Electric OM-2241 is also engineered with durability in mind. Constructed with high-quality materials and protective features, it can withstand challenging working environments and ensure long-lasting operation. This resilience is complemented by Miller’s reputation for reliability and customer satisfaction, providing peace of mind to users.

In conclusion, the Miller Electric OM-2241 stands out in the welding equipment market due to its multifaceted capabilities, user-friendly technologies, and robust performance characteristics. Whether in a workshop or at a job site, this welding machine delivers the versatility and reliability required for various welding applications, making it an essential tool for any welder's arsenal.
Top Page Image Contents