Miller Electric XMT 456CV manual Volt-Ampere Curves, Dimensions And Weight, CV Modes CC Modes

Page 20

4-3. Volt-Ampere Curves

CV Modes

CC Modes

Volt-ampere curves show mini- mum and maximum voltage and amperage output capabilities of unit. Curves of other settings fall be- tween curves shown.

va_curve1 4/95 − SA-181 561 / SA-181 562

4-4. Dimensions And Weight

 

Hole Layout Dimensions

 

F

 

 

 

 

 

 

A

A

14-21/64 in (363.9 mm)

 

 

B

20-3/4 in (527.1 mm)

 

28 in

 

(711 mm)

 

 

 

C

23-27/64 in (594.9 mm)

 

 

D

24-31/32 in (634.2 mm)

 

18 in

C

(457 mm)

 

D

 

B

E

12-3/8 in (314.3 mm)

 

 

 

F

9/32 in (7.1 mm) Dia.

 

 

 

 

 

15-1/2 in

 

Weight

 

(394 mm)

 

 

 

 

118 lb (53.5 kg)

 

E

OM-203 034 Page 16

 

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OM-203 034N ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Decstat6/05 DirectivesStandards Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-203 034 Keep your head out of the fumes Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions 60 s Symbols And Definitions I1maxI1eff Weee LabelManufacturer’s Rating Labels Specifications Duty Cycle And OverheatingCV Modes CC Modes Dimensions And WeightVolt-Ampere Curves Connecting To Weld Terminals Selecting a LocationMovement Tipping Location350 ft 400 ft Put terminals Weld Output Terminals And Selecting Cable SizesARC Welding can cause Electromagnetic Interference Connecting Weld Output Cables Remote 14 Receptacle InformationElectrical Service Guide Hz Three PhaseVolts AC Duplex Receptacle Input VoltageConnecting Input Power Input Filter BoardAlways connect grounding conductor first L21 Tools NeededMode And Voltage Control For CV Only Models Mode ControlFront Panel Controls For CV Only Models Voltage ControlPreset Volts Blank Power SwitchMeter Functions For CV Only Models Front Panel Controls For CC/CV ModelsMeter Functions For CC/CV Models Panel Control GtawHold TIG Gtaw Blank Pulsed MIGMode Switch Settings For CC/CV Models Lift-Arc TIG Procedure For CC/CV Models Touch Seconds Do not Strike Like a MatchDo not remove case when blowing out inside of unit Blowing Out Inside Of UnitRemoving Case and Measuring Input Capacitor Voltage Voltmeter/Ammeter Help Displays Troubleshooting Reset circuit breaker CB1 see SectionOM-203 034 − Electrical Diagram 203 505-A Circuit Diagram For CC/CV Welding Power Source 204 950−B Complete Assembly 39 40 41Dia Part Description Quantity Mkgs 180 Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s
Top Page Image Contents