Miller Electric Dimension 1000 manual Tipping, Do not move or operate unit where it could tip

Page 20

4-6. Tipping

! Do not move or operate unit where it could tip.

4-7. 115 VAC Receptacle, Supplementary Protectors, And Weld Output Terminals

3

2

1

			!	Turn Off power before
				connecting to receptacle, or
				weld output terminals.
			1	115 V 15 A AC Receptacle
				RC9
			Power is shared between RC9, Re-
			mote 14 receptacle RC8 and termi-
			nal strip 1T (see Section 4-11).
			2	Supplementary Protector CB1
			3	Supplementary Protector CB2
			CB1 protects 115 volts ac portion of
			RC8, 1T, and RC9 from overload.
			CB2 protects 24 volts ac portion of
			RC8 and 1T from overload.
			Press button to reset protector.
			4	Positive High Inductance
				(Submerged Arc) Weld Output
				Terminal
			Use this terminal for Submerged
			Arc (SAW), TIG (GTAW)-scratch
	5	6	start only, or Stick (SMAW) applica-
4	5	6	tions.
			5	(+) Positive Low Inductance
				Weld output terminal
			Not recommended for Submerged
			Arc applications.
			6	(−) Negative Weld Output
				Terminal

Connect work cable to this terminal for Submerged Arc applications.

Ref. 802 295

OM-2223 Page 16

Image 20

Contents File Multiprocess ProcessesDescription From Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF Work like a Pro Symbol Definitions SpecificationsI1max I1effDuty Cycle And Overheating 100% Duty CycleCC Mode CV Mode Volt-Ampere CurvesSelecting a Location MovementWeight Dimensions And WeightsDimensions Do not move or operate unit where it could tip Turn Off power beforeTipping Weld output terminalsBasic Sub Arc SAW Welding Basic Sub Arc SAW Equipment ConnectionsControl Settings For Sub Arc SAW Welding Welding Power Source Sensing Leads Placement Guidelines For Multiple Arcs BetterSelecting Cable Sizes Remote 14 Receptacle And Terminal Strip 1T InformationConnecting Remote Control Turn off power before con- necting to receptacleElectrical Service Guide Placing Jumper LinksDisconnect Device Input Power Connec- tions Connecting Input PowerWelding Power Source Input Power Connections − Operation ControlsMonths Routine MaintenanceFuse F1 Troubleshooting Trouble Remedy− Electrical Diagram 236 682-A − Parts List PLG14 Panel, Front w/Components -1Item PLG10 Rectifier, SCR Main -1Item Panel, Rear w/Components -1Item Page Page Page Service SupportOwner’s Record Miller Electric Mfg. Co