Miller Electric 452, 652 (60 Hz) Input Connection Label, Electric Shock And Airflow Label, ? a

Page 16

.A complete Parts List is available at www.MillerWelds.com

3-2. Input Connection Label

1		2		3	4
1	2			3	? V
	? V
	? A				5
					5
					3
				4
					S-179 290
5	6	7	8		9

1 Warning! Watch Out! There are possible hazards as shown by the symbols.

2 Electric shock from wiring can kill.

3 Disconnect input plug or power before working on machine.

4 Read the Owner’s Manual

before working on this machine.

5 Consult rating label for input power requirements, and check power available at the job site − they must match.

6 Read Owner’s Manual and inside labels for connection points and procedures.

7 Move jumper links as shown on inside label to match voltage at job site.

8 Having a loop of extra length, connect grounding conductor first.

9 Connect line input conductors as shown on inside label − double-check all connections, jumper link positions, and input voltage before applying power.

1/96

3-3. Electric Shock And Airflow Label

1

2

3

S-179 563

1Warning! Watch Out! There are possible hazards as shown by the symbols.

2Electric shock from wiring and exposed weld terminals can kill.

3Close door before turning on unit.

1/96

3-4. Nameplate Safety Symbols

				1	Warning! Watch Out! There
					are possible hazards as
	1	1			shown by the symbols.
	1	1		2	Electric shock from welding
				2	Electric shock from welding
					electrode or wiring can kill.
				3	Sparks from arcing electrode
					can cause explosion or fire −
					disconnect cable for process
					not in use.
				4	Read Owner’s Manual for
					connection procedures.
				5	Electric shock from wiring can
					kill.
		5	6	6	Disconnect input power
		5	6		before working on unit or
2	3	4			before working on unit or
2	3	4			making terminal strip
					making terminal strip

connections.

Nameplate D-179 389

OM-222 Page 8

Image 16

Contents Arc Welding Power Source ProcessesDescription File Stick SmawFrom Miller to You Table of Contents Standards DirectivesDecstat6/05 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-222 General Precautionary Label − DefinitionsNameplate Safety Symbols Input Connection LabelElectric Shock And Airflow Label ? aManufacturer’s Rating Labels For CE Products Symbols And Definitions Weee Label For Products Sold Within The EUSpecifications − InstallationDuty Cycle And Overheating Volt-Ampere Curves Amp ModelSelecting a Location Location And AirflowDimensions And Weights Dimensions Amp ModelsWeight 352 lb 160 kg 404 lb 183 kg 505 lb 229 kg Holes EFrontVAC Receptacle And Supplementary Protectors TippingWeld Output Terminals Connecting Weld Output Cables Selecting Cable SizesConnecting Remote Control Remote 14 Receptacle InformationInformation To remote On/O ff sw itchElectrical Service Guide Placing Jumper Links Tools Needed Do not overtighten Jumper link nutsConnecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Connec- tions = GND/PE Earth GroundTurn Off Power before reversing cables Turn Off power before connecting re- mote device− Operation Controls Non CE ModelsControls CE Models − Maintenance and Troubleshooting Routine MaintenanceDisconnect power before maintaining Fuse F1Reset supplementary protector CB1 see Section TroubleshootingTrouble Remedy OM-222 − Electrical Diagram Circuit Diagram218 518-A Recommended Spare Parts − Parts ListRecommended Spare Parts Page Page Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s