Miller Electric 602, 652 (60 Hz), 402, 302, 452 manual Selecting a Location, Location And Airflow

Page 21

. A complete Parts List is available at www.MillerWelds.com

4-4. Selecting A Location

	1	Lifting Eye
	2	Lifting Forks
	Use lifting eye or lifting forks to
	move unit.
Movement	If using lifting forks, extend forks
Movement	beyond opposite side of unit.
	beyond opposite side of unit.
1	3	Rating Label Location
	Use rating label to determine input
	power needs. Label located under
	front access door.
	4	Rating Label (CE Models

	OR	Only)
	2	Use rating label to determine input
		power needs. Label located on rear
		access door (see Section 3-5).
Location And Airflow		5 Line Disconnect Device
Location And Airflow	5	Locate unit near correct input pow-
	5	Locate unit near correct input pow-

er supply.

18 in

(460 mm)

18in

(460 mm)

Special installation may be required where gasoline or volatile liquids are present − see NEC Article 511 or CEC Section 20.

OM-222 Page 13

Image 21

Contents Processes Arc Welding Power SourceDescription File Stick SmawFrom Miller to You Table of Contents Directives StandardsDecstat6/05 Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-222 − Definitions General Precautionary LabelInput Connection Label Nameplate Safety SymbolsElectric Shock And Airflow Label ? aManufacturer’s Rating Labels For CE Products Weee Label For Products Sold Within The EU Symbols And Definitions− Installation SpecificationsDuty Cycle And Overheating Amp Model Volt-Ampere CurvesLocation And Airflow Selecting a LocationDimensions Amp Models Dimensions And WeightsWeight 352 lb 160 kg 404 lb 183 kg 505 lb 229 kg Holes EFrontTipping VAC Receptacle And Supplementary ProtectorsWeld Output Terminals Selecting Cable Sizes Connecting Weld Output CablesRemote 14 Receptacle Information Connecting Remote ControlInformation To remote On/O ff sw itchElectrical Service Guide Tools Needed Do not overtighten Jumper link nuts Placing Jumper LinksWelding Power Source Input Power Connections Connecting Input PowerDisconnect Device Input Power Connec- tions = GND/PE Earth GroundTurn Off power before connecting re- mote device Turn Off Power before reversing cables− Operation Controls Non CE ModelsControls CE Models Routine Maintenance − Maintenance and TroubleshootingDisconnect power before maintaining Fuse F1Troubleshooting Reset supplementary protector CB1 see SectionTrouble Remedy OM-222 Circuit Diagram − Electrical Diagram218 518-A − Parts List Recommended Spare PartsRecommended Spare Parts Page Page Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s