Installation Procedure, Step Two Positioning

Model	Weight(kg)
	Empty	Full
Five Litre
over-sink	3.5	8.5
Ten Litre	4.0	14.0
under-sink	4.0	14.0
Five Litre	3.5	8.5
over-sink	3.5	8.5
Ten Litre
under-sink	4.0	14.0

Installation Procedure continued

Step Two - Positioning

Over-sink heaters should be installed so that the outlet spout drains to a sink or basin, and with a clearance of 270 mm beneath the heater to allow for service access.

Under-sink heaters should be installed a closely as possible to directly below the outlet tap with a clearance of 270 mm above the heater.

Step Three - Fastening

It is not necessary to remove the case of the heater during installation.

The heater must be wall mounted with two fixing screws as shown in the diagram on page 5. Fixing screws must have the strength to support the filled heater.

The fixing screws are to protrude 4 mm from the wall as shown in the diagram on page 5 so as to fit into keyhole slots provided on the rear of the heater.

Step Four - Connecting

On over-sink models, the inlet and outlet are located on the base of the heater.

On under-sink models, the inlet and outlet are located on the top of the heater.

All Zenith Tudor water connections are via 15 mm compression fittings and must be made strictly as shown in the diagrams.

Over-sink models are supplied with a 300 mm open outlet spout, and must also be fitted with an isolation valve on the cold water side. A valve is not supplied with the heater and must be supplied and fitted by the installer.

Under-sink models must be installed with approved vented tapware regulating the incoming water supply which displaces the hot water from the heater so it discharges through the open vented spout incorporated into the tap mounted on the basin or sink.

The use of tapware other than approved vented tapware is dangerous.

Each heater is equipped with a 1600 mm power cord and plug and should be connected to a standard 10 amp power outlet located adjacent to the heater.

Do not turn the power ON until the heater is filled with water and air is purged from the heater.

Step Five - Commissioning

Fill the heater tank and purge air from the heater by turning the water supply ON and running water through the heater until it flows smoothly. Turn the water supply OFF and turn the power supply ON. The heater will then run through its heating cycle.

During the heating cycle, drips fall from the delivery spout or tap.

Dripping will cease when the heating cycle is completed and the stored water temperature has reached the level set by the user.

Page 4

ZenithipTudorTudor- Installation- Installation& &OperatingOperatingInstructionsInstructions- 81333- 81 3- July- May- 20043

216666666 specifications

Zenith 216666666 is a remarkable timepiece that represents the pinnacle of Swiss watchmaking craftsmanship and innovation. Known for its exquisite design and advanced technology, this watch stands out in the luxury segment, appealing to collectors and enthusiasts alike.

One of the main features of the Zenith 216666666 is its exceptional movement. Powered by the renowned El Primero chronograph caliber, this watch boasts an impressive frequency of 36,000 vibrations per hour, allowing for precise timekeeping and enhanced accuracy. The El Primero movement has garnered a reputation for its reliability and performance, making it a hallmark of Zenith's engineering prowess.

The design of the Zenith 216666666 is equally striking. The case is meticulously crafted from high-grade stainless steel, providing durability while maintaining a sophisticated appearance. It features a polished finish that enhances its aesthetic appeal. The watch face is adorned with a stunning array of sub-dials, providing functionality while adding to the visual complexity of the timepiece. The sapphire crystal is anti-reflective, ensuring excellent legibility under varying lighting conditions.

One of the standout characteristics of the Zenith 216666666 is its commitment to precision. The chronograph function allows for timing events with remarkable accuracy, and the tachymetric scale on the bezel enhances its utility for speed measurements. This makes the watch not only an elegant accessory but also a functional tool for professionals and enthusiasts in various fields.

The watch also incorporates modern technology, such as a transparent case back that reveals the intricate mechanics of the El Primero movement. This feature allows wearers to appreciate the artistry of the watch's inner workings, showcasing the intricate details and craftsmanship that go into each piece.

In terms of water resistance, the Zenith 216666666 is designed to withstand daily wear and tear, making it suitable for both casual and formal occasions. The meticulous attention to detail in the watch’s construction ensures that it remains a lasting investment.

Overall, Zenith 216666666 embodies the fusion of traditional watchmaking artistry and cutting-edge technology. With its robust movement, elegant design, and practical features, it is a testament to Zenith's commitment to excellence in horology, making it a prized possession for any watch lover.