Step One Tapware | Zenith 216666666 specs

Before installing, ensure that theInstallationfo owingRequirementsare available:

Before installing, ensure that the following are available:

a)sufficient space to position the heater so there is 270 mm clear access under the heater (over-sink models) or 270mm above (under-sink).

b)standard 10 amp 240 volt power outlet within 1500 mm of the heater

c)cold water supply with a minimum working pressure of 50 kPa and a maximum working pressure of 750 kPa.

If pressure may exceed 750 kPa, a pressure limiting valve must be installed.

Under-sink models must be installed beneath approved vented mixer taps requiring a single mounting point on a sink, basin or tub.

Water pressure under 100 kPa may be sufficient for over-sink heaters but may not operate under-sink mixer taps satisfactorily.

Before installing, ensure that theInstallationfol owingProcedurea e available:

	HERO MIXER	SOLO MIXER
	Cold Water	B Cold Water
	Supply from Tap	B Cold Water
	Supply from Tap	Supply to Heater
	A	Supply to Heater
	A
	C	Fixing Bolt
	Hot Water
	Supply from Heater

MONO MIXER

Cold Water Supply to

BHeater

Fixing Bolt

Hot Water	C			A
Supply from		Heater	Cold Water
			Supply from Tap

Step One - Tapware

Over-sink models must be installed with an inlet valve to control the flow from the water supply to the heater. No valve is supplied with the heater. The water supply and valve should be connected after the fastening the heater to the wall.

Over-sink models are supplied with a 300 mm swivel spout. An 300 mm to 600 mm telescopic swivel spout (99032) is available as an optional extra.

Under-sink models must be installed with approved vented tapware. It is advisable to fit the tap to the sink before mounting the heater to the wall beneath the sink.

1.Ensure that the flexible tubes are firmly attached to the base of the tap body.

2.Flush water supply pipes thoroughly to remove any silt or fines.

3.Fasten the tap body to the sink using the bolt & plate system provided.

4.Connect red flexible tube (from tap base "C") to the heater outlet.

5.Insert flow restrictor provided to the free end of blue flexible tube "A"

ONLY IF the water pressure is likely to exceed 250 kPa. Otherwise discard restrictor.

6.Connect blue flexible tube (from tap base "B" ) to the heater inlet.

7.Connect blue flexible tube (from tap base "A") to the cold water supply.

Do not dismantle the assembled tap body during installation. Mixer taps are factory tested and sealed to provide optimum performance.

To adjust water temperature delivered by Solo and Hero mixer taps, see instructions on page 7. Such adjustments should be made only by a qualified technician.

Note: If replacing an existing open outlet (vented) water heater an isolation valve must be fitted to the incoming water supply and a 7L/min flow restrictor fitted at the isolation valve outlet. It is essential to establish that any existing tapware is vented.


ZenithZpenithTudorTudor- Installation- Installation& Operating& OperatingI strucInstructionsions - 81333- 81333- May- July2003- 2004	Page 3	Page 3

216666666 specifications

Zenith 216666666 is a remarkable timepiece that represents the pinnacle of Swiss watchmaking craftsmanship and innovation. Known for its exquisite design and advanced technology, this watch stands out in the luxury segment, appealing to collectors and enthusiasts alike.

One of the main features of the Zenith 216666666 is its exceptional movement. Powered by the renowned El Primero chronograph caliber, this watch boasts an impressive frequency of 36,000 vibrations per hour, allowing for precise timekeeping and enhanced accuracy. The El Primero movement has garnered a reputation for its reliability and performance, making it a hallmark of Zenith's engineering prowess.

The design of the Zenith 216666666 is equally striking. The case is meticulously crafted from high-grade stainless steel, providing durability while maintaining a sophisticated appearance. It features a polished finish that enhances its aesthetic appeal. The watch face is adorned with a stunning array of sub-dials, providing functionality while adding to the visual complexity of the timepiece. The sapphire crystal is anti-reflective, ensuring excellent legibility under varying lighting conditions.

One of the standout characteristics of the Zenith 216666666 is its commitment to precision. The chronograph function allows for timing events with remarkable accuracy, and the tachymetric scale on the bezel enhances its utility for speed measurements. This makes the watch not only an elegant accessory but also a functional tool for professionals and enthusiasts in various fields.

The watch also incorporates modern technology, such as a transparent case back that reveals the intricate mechanics of the El Primero movement. This feature allows wearers to appreciate the artistry of the watch's inner workings, showcasing the intricate details and craftsmanship that go into each piece.

In terms of water resistance, the Zenith 216666666 is designed to withstand daily wear and tear, making it suitable for both casual and formal occasions. The meticulous attention to detail in the watch’s construction ensures that it remains a lasting investment.

Overall, Zenith 216666666 embodies the fusion of traditional watchmaking artistry and cutting-edge technology. With its robust movement, elegant design, and practical features, it is a testament to Zenith's commitment to excellence in horology, making it a prized possession for any watch lover.