Miller Electric 145 DXR, 145 manual Servicing Air Cleaner, Stop engine, Precleaner Paper Element

Page 30

. Complete Parts List available at www.MillerWelds.com

8-2. Servicing Air Cleaner

! Stop engine.

NOTICE − Do not run engine with- out air cleaner or with dirty element.

1 Precleaner

2 Paper Element

		. Do not wash paper element or
		clean with compressed air.
		Remove cover.
		Wash precleaner with soap and wa-
		ter solution. Allow precleaner to air
		dry completely.
		Dip precleaner in clean engine oil.
		Squeeze out excess oil. The engine
	1	will smoke if precleaner contains
	1	too much oil.
		too much oil.
		Replace paper element if dirty, oily,
		or damaged.
	2

Standard Model Shown

oil

aircleaner6 9/00 − 803 404

OM-4417 Page 26

Image 30

Contents Description OM-4417210 403FProcesses File Engine DriveFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousBuildup of GAS can injure or kill Welding can cause fire or explosionEngine Hazards Compressed Air HazardsFire or Explosion hazard Welding Wire can cause injuryHOT Parts can cause burns and injury Falling Unit can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings Radiation can cause interferenceSignification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peuDES Organes Mobiles peuvent pro voquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessuresRisque D’INCENDIE OU D’EXPLO- Sion LES Fils DE Soudage peuvent provoquer des blessures LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures ’EMPLOI Excessif peutProposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF Weld, Power, And Engine Specifications − SpecificationsSymbol Definitions − DefinitionsDimensions, Weights, And Operating Angles DimensionsVolt-Ampere Curves Fuel Consumption 100% Duty Cycle at 80 Amperes CC/DC Generator Power CurveDuty Cycle Minutes WeldingMovement − InstallationInstalling Welding Generator HazardsGrounding Generator When Supplying Building Systems Engine Prestart Checks − Standard ModelOil Connecting The Battery DX Models Only Engine Prestart Checks − DX Model45 m 60 m 70 m 90 m 105 m 120 m 10 − Connecting To Weld Output TerminalsSelecting Weld Cable Sizes Put terminals− Operating the Welding Generator Controls Standard Models See SectionDescription Of Controls Standard Models See Section Stop engine and add oil if light goes on see SectionTo Start Controls DX Models See Section Description Of Controls DX Models See Section Generator Power Panel Receptacles − Operating Auxiliary EquipmentAC Receptacle RC1 − Maintenance Routine MaintenanceStop engine Servicing Air CleanerPrecleaner Paper Element Standard Model ShownValve Adjusting Engine Speed Standard Models OnlyStop Engine Close Tools NeededAdjusting Engine Speed DX Models Only Weld/Power Speed AdjustmentIdle Speed Adjustment Generator Power − TroubleshootingTroubleshooting WeldingEngine − Parts List Recommended Spare PartsRecommended Spare Parts − Electrical Diagrams Circuit Diagram For Standard ModelsCircuit Diagram for DX Models − Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Industrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsSingle-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP x 1000 / Volts = Starting AmperageTypical Connections To Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord PossibleCord Lengths for 120 Volt Loads Cord Lengths for 240 Volt LoadsStick Welding Procedure − Stick Welding Smaw GuidelinesElectrode and Amperage Selection Chart Striking an Arc − Scratch Start TechniqueStriking an Arc − Tapping Technique Positioning Electrode Holder Poor Weld Bead CharacteristicsGood Weld Bead Characteristics 10-30 9090 End View of Work AngleConditions That Affect Weld Bead Shape Electrode Movement During WeldingTee Joint Butt JointsLap Joint 16 in 30 1.6 mm Tack WeldsWeld Test Troubleshooting − PorosityTroubleshooting − Excessive Spatter Possible Causes Corrective ActionsTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Excessive Penetration Troubleshooting − Burn-Through Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Service Your distributor also givesSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s