Miller Electric Blue Star 145, 145 DXR, 145 manual Your distributor also gives, Service, Support

Page 53
miller_warr 2007−01

Warranty Questions?

Effective January 1, 2007 (Equipment with a serial number preface of “LH” or newer)

This limited warranty supersedes all previous Miller warranties and is exclusive with no other

guarantees or warranties expressed or implied.

Call

1-800-4-A-MILLER for your local Miller distributor.

Your distributor also gives

you ...

Service

You always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours.

Support

Need fast answers to the tough welding questions? Contact your distributor.

The expertise of the distributor and Miller is there to help you, every step of the way.

LIMITED WARRANTY − Subject to the terms and conditions below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its original retail purchaser that new Miller equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped by Miller. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

Within the warranty periods listed below, Miller will repair or replace any warranted parts or components that fail due to such defects in material or workmanship. Miller must be notified in writing within thirty (30) days of such defect or failure, at which time Miller will provide instructions on the warranty claim procedures to be followed.

Miller shall honor warranty claims on warranted equipment listed below in the event of such a failure within the warranty time periods. All warranty time periods start on the delivery date of the equipment to the original end-user purchaser, and not to exceed one year after the equipment is shipped to a North American distributor or eighteen months after the equipment is shipped to an International distributor.

1.5 Years Parts — 3 Years Labor

*Original main power rectifiers

2.3 Years — Parts and Labor

*Transformer/Rectifier Power Sources

*Plasma Arc Cutting Power Sources

*Process Controllers

*Semi-Automatic and Automatic Wire Feeders

*Inverter Power Sources (Unless Otherwise Stated)

*Water Coolant Systems (Integrated)

*Intellitig

*Engine Driven Welding Generators

(NOTE: Engines are warranted separately by the engine manufacturer.)

3.1 Year — Parts and Labor Unless Specified

*Motor Driven Guns (w/exception of Spoolmate Spoolguns)

*Positioners and Controllers

*Automatic Motion Devices

*RFCS Foot Controls

*Induction Heating Power Sources, Coolers, and Electronic

Controls/Recorders

*Water Coolant Systems (Non-Integrated)

*Flowgauge and Flowmeter Regulators (No Labor)

*HF Units

*Grids

*Spot Welders

*Load Banks

*Arc Stud Power Sources & Arc Stud Guns

*Racks

*Running Gear/Trailers

*Plasma Cutting Torches (except APT & SAF Models)

*Field Options

(NOTE: Field options are covered under True Blue→ for the remaining warranty period of the product they are installed in, or for a minimum of one year — whichever is greater.)

*Bernard-Branded Mig Guns (No Labor)

*Weldcraft-Branded TIG Torches (No Labor)

*Subarc Wire Drive Assemblies

4.6 Months — Batteries

5.90 Days — Parts

*MIG Guns/TIG Torches and Subarc (SAW) Guns

*Induction Heating Coils and Blankets, Cables, and Non-Electronic Controls

*APT & SAF Model Plasma Cutting Torches

*Remote Controls

*Accessory (Kits)

*Replacement Parts (No labor)

*Spoolmate Spoolguns

*Canvas Covers

Miller’s True Blue→ Limited Warranty shall not apply to:

1.Consumable components; such as contact tips, cutting nozzles, contactors, brushes, slip rings, relays or parts that fail due to normal wear. (Exception: brushes, slip rings, and relays are covered on Bobcat, Trailblazer, and Legend models.)

2.Items furnished by Miller, but manufactured by others, such as engines or trade accessories. These items are covered by the manufacturer’s warranty, if any.

3.Equipment that has been modified by any party other than Miller, or equipment that has been improperly installed, improperly operated or misused based upon industry standards, or equipment which has not had reasonable and necessary maintenance, or equipment which has been used for operation outside of the specifications for the equipment.

MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS TRAINED AND EXPERIENCED IN THE USE AND MAINTENANCE OF WELDING EQUIPMENT.

In the event of a warranty claim covered by this warranty, the exclusive remedies shall be, at Miller’s option: (1) repair; or (2) replacement; or, where authorized in writing by Miller in appropriate cases, (3) the reasonable cost of repair or replacement at an authorized Miller service station; or (4) payment of or credit for the purchase price (less reasonable depreciation based upon actual use) upon return of the goods at customer’s risk and expense. Miller’s option of repair or replacement will be F.O.B., Factory at Appleton, Wisconsin, or F.O.B. at a Miller authorized service facility as determined by Miller. Therefore no compensation or reimbursement for transportation costs of any kind will be allowed.

TO THE EXTENT PERMITTED BY LAW, THE REMEDIES PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY.

ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED BY MILLER.

Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion of incidental, indirect, special or consequential damages, so the above limitation or exclusion may not apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary from state to state.

In Canada, legislation in some provinces provides for certain additional warranties or remedies other than as stated herein, and to the extent that they may not be waived, the limitations and exclusions set out above may not apply. This Limited Warranty provides specific legal rights, and other rights may be available, but may vary from province to province.

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Processes OM-4417210 403FDescription File Engine DriveFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsBuildup of GAS can injure or kill Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionCompressed Air Hazards Engine HazardsHOT Parts can cause burns and injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information Radiation can cause interferenceUN Choc Électrique peut tuer Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux DES Organes Mobiles peuvent pro voquer des blessures LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peu Risque D’INCENDIE OU D’EXPLO- Sion LA Chaleur DU Moteur peut pro- voquer un incendie’AIR Comprimé peut provoquer des blessures DES Organes Mobiles peuvent provoquer des blessures LE Surchauffement peut endom- mager le moteur électriqueLES Fils DE Soudage peuvent provoquer des blessures ’EMPLOI Excessif peutInformation EMF Proposition californienne 65 AvertissementsPrincipales normes de sécurité Symbol Definitions − SpecificationsWeld, Power, And Engine Specifications − DefinitionsVolt-Ampere Curves Dimensions, Weights, And Operating AnglesDimensions Fuel Consumption Duty Cycle Generator Power Curve100% Duty Cycle at 80 Amperes CC/DC Minutes WeldingInstalling Welding Generator − InstallationMovement HazardsOil Grounding Generator When Supplying Building SystemsEngine Prestart Checks − Standard Model Engine Prestart Checks − DX Model Connecting The Battery DX Models OnlySelecting Weld Cable Sizes Connecting To Weld Output Terminals45 m 60 m 70 m 90 m 105 m 120 m 10 − Put terminalsControls Standard Models See Section − Operating the Welding GeneratorTo Start Description Of Controls Standard Models See SectionStop engine and add oil if light goes on see Section Controls DX Models See Section Description Of Controls DX Models See Section AC Receptacle RC1 Generator Power Panel Receptacles− Operating Auxiliary Equipment Routine Maintenance − MaintenancePrecleaner Paper Element Servicing Air CleanerStop engine Standard Model ShownStop Engine Close Adjusting Engine Speed Standard Models OnlyValve Tools NeededIdle Speed Adjustment Adjusting Engine Speed DX Models OnlyWeld/Power Speed Adjustment Troubleshooting − TroubleshootingGenerator Power WeldingEngine Recommended Spare Parts − Parts ListRecommended Spare Parts Circuit Diagram For Standard Models − Electrical DiagramsCircuit Diagram for DX Models Grounding Generator To Truck Or Trailer Frame − Generator Power GuidelinesSelecting Equipment How Much Power Does Equipment Require? Grounding When Supplying Building SystemsApproximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentHow Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting AmperageTypical Connections To Supply Standby Power Cord Lengths for 120 Volt Loads Selecting Extension Cord Use Shortest Cord PossibleCurrent Load Watts Amperes Cord Lengths for 240 Volt Loads− Stick Welding Smaw Guidelines Stick Welding ProcedureStriking an Arc − Tapping Technique Electrode and Amperage Selection ChartStriking an Arc − Scratch Start Technique Good Weld Bead Characteristics Poor Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work AngleElectrode Movement During Welding Conditions That Affect Weld Bead ShapeLap Joint Butt JointsTee Joint 16 in 30 1.6 mm Tack WeldsTroubleshooting − Excessive Spatter Troubleshooting − PorosityWeld Test Possible Causes Corrective ActionsTroubleshooting − Excessive Penetration Troubleshooting − Incomplete FusionTroubleshooting − Lack Of Penetration Troubleshooting − Distortion Troubleshooting − Burn-ThroughTroubleshooting − Waviness Of Bead Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s
Top Page Image Contents