Miller Electric 456 CC manual Volt-Ampere Curves, Dimensions And Weight, CV Modes CC Modes

Page 19

4-3. Volt-Ampere Curves

CV Modes

CC Modes

Volt-ampere curves show mini- mum and maximum voltage and amperage output capabilities of unit. Curves of other settings fall be- tween curves shown.

va_curve1 4/95 − SA-181 561 / SA-181 562

4-4. Dimensions And Weight

 

Hole Layout Dimensions

 

F

 

 

 

 

 

 

A

A

14-21/64 in (363.9 mm)

 

 

B

20-3/4 in (527.1 mm)

 

28 in

 

(711 mm)

 

 

 

C

23-27/64 in (594.9 mm)

 

 

D

24-31/32 in (634.2 mm)

 

18 in

C

(457 mm)

 

D

 

B

E

12-3/8 in (314.3 mm)

 

 

 

F

9/32 in (7.1 mm) Dia.

 

 

 

 

 

15-1/2 in

 

Weight

 

(394 mm)

 

 

 

 

118 lb (53.5 kg)

 

E

 

 

 

OM-203 034 Page 15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents File MIG Gmaw OM-203 034RProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-203 034 Manufacturer’s Warning Label Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes 60 s Weee Label Symbols And DefinitionsI1max I1effDuty Cycle And Overheating SpecificationsVolt-Ampere Curves Dimensions And WeightCV Modes CC Modes Location Connecting To Weld TerminalsSelecting a Location Movement TippingARC Welding can cause Electromagnetic Interference Weld Output Terminals And Selecting Cable Sizes350 ft 400 ft Put terminals Remote 14 Receptacle Information Connecting Weld Output CablesInput Voltage Electrical Service GuideHz Three Phase Volts AC Duplex ReceptacleL21 Tools Needed Connecting Input PowerInput Filter Board Always connect grounding conductor firstVoltage Control Mode And Voltage Control For CV Only ModelsMode Control Front Panel Controls For CV Only ModelsFront Panel Controls For CC/CV Models Preset Volts BlankPower Switch Meter Functions For CV Only ModelsPulsed MIG Meter Functions For CC/CV ModelsPanel Control Gtaw Hold TIG Gtaw BlankMode Switch Settings For CC/CV Models Touch Seconds Do not Strike Like a Match Lift-Arc TIG Procedure For CC/CV ModelsBlowing Out Inside Of Unit Do not remove case when blowing out inside of unitRemoving Case and Measuring Input Capacitor Voltage Voltmeter/Ammeter Help Displays Reset circuit breaker CB1 see Section Troubleshooting− Electrical Diagram 239 524-A Circuit Diagram For CC/CV Welding Power Source 239 526-A 39 40 41 Complete AssemblyDia Part Description Quantity Mkgs 180 Material Thickness Gauge Work like a Pro Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact
Related manuals
Manual 40 pages 21.64 Kb
Top Page Image Contents