Miller Electric 456 CC manual Selecting a Location, Connecting To Weld Terminals, Movement Tipping

Page 20

4-5. Selecting A Location

Movement

	2
OR	3
OR

Tipping

Do not move or operate unit where it could tip.

Location

18 in

(460 mm)

18 in

(460 mm)

1 Lifting Forks

Use lifting forks to move unit.

Extend forks beyond opposite side of unit.

2Lifting Handles Use handles to lift unit.

3Hand Cart

Use cart or similar device to move unit.

4 Rating Label - Typical

4Use rating label to determine input power needs.

5 Line Disconnect Device

Locate unit near correct input power supply.

! Special installation may be required where gasoline or volatile liquids are present − see NEC Article 511 or CEC Section 20.

loc_2 3/96 - 800 611 / 802 260

4-6. Connecting To Weld Terminals

! Turn off power before con- necting to weld output ter- minals.

1 Positive (+) Weld Output Terminal

2 Negative (−) Weld Output Terminal

Connect positive weld cable to Positive (+) weld terminal and negative (−) cable to Negative weld terminal.

Tools Needed:

Ref. 802 260

OM-203 034 Page 16

Image 20

Contents OM-203 034R ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-203 034 Keep your head out of the fumes Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions 60 s Symbols And Definitions I1maxI1eff Weee LabelSpecifications Duty Cycle And OverheatingCV Modes CC Modes Dimensions And WeightVolt-Ampere Curves Connecting To Weld Terminals Selecting a LocationMovement Tipping Location350 ft 400 ft Put terminals Weld Output Terminals And Selecting Cable SizesARC Welding can cause Electromagnetic Interference Connecting Weld Output Cables Remote 14 Receptacle InformationElectrical Service Guide Hz Three PhaseVolts AC Duplex Receptacle Input VoltageConnecting Input Power Input Filter BoardAlways connect grounding conductor first L21 Tools NeededMode And Voltage Control For CV Only Models Mode ControlFront Panel Controls For CV Only Models Voltage ControlPreset Volts Blank Power SwitchMeter Functions For CV Only Models Front Panel Controls For CC/CV ModelsMeter Functions For CC/CV Models Panel Control GtawHold TIG Gtaw Blank Pulsed MIGMode Switch Settings For CC/CV Models Lift-Arc TIG Procedure For CC/CV Models Touch Seconds Do not Strike Like a MatchDo not remove case when blowing out inside of unit Blowing Out Inside Of UnitRemoving Case and Measuring Input Capacitor Voltage Voltmeter/Ammeter Help Displays Troubleshooting Reset circuit breaker CB1 see Section− Electrical Diagram 239 524-A Circuit Diagram For CC/CV Welding Power Source 239 526-A Complete Assembly 39 40 41Dia Part Description Quantity Mkgs 180 Material Thickness Gauge Work like a Pro Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Related manuals

Manual 40 pages 21.64 Kb