Bad Boy Mowers 02.9812.0001C Setting a Starting Address, DMX Comm, To program a starting address

Page 33

INSTALLATION : POWER UP AND BASIC SETUP PROCEDURES 2

Setting a Starting Address

The method for setting a DMX starting address is the same whether the luminaire is being controlled by DMX512 or Ethernet (Art-Net). The only difference is that the Home screen will display the Comm as either "DMX" or "ETH" depending on the control input.

The DMX starting address is programmed at the Menu Touchscreen. The luminaire retains its address even if power is removed.

Note: Refer to your console operating instructions for specific information regarding its addressing requirements.

DMX Comm

The starting address for DMX512 systems is programmed using the CONFIG menu.

To program a starting address:

Step

1.

At Home screen, press CONFIG panel.

Step

2.

At Configuration screen, press DMX ADDRESS panel.

Step

3.

At numeric keypad, enter new starting address and press ENTER.

Control Input Type

Figure 2-13: Setting Starting Address (DMX Control)

Note: Refer to "Menu System" on page 30 for more information about the Menu Touchscreen.

02.9812.0001C

23

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Spot Luminaire Production Resource Group, LLC. All Rights Reserved Compliance Notice Safety Notice02.9812.0001C Iii This manual has been revised as follows Revision HistoryTable of Contents Operation Troubleshooting and MaintenanceAppendix A. Technical Specifications Routine MaintenanceAppendix B. Glossary Viii Introduction About This ManualAdditional Documentation PRG Dallas International Service PRG Atlanta Customer ServiceGobo Art Submission Guidelines 02.9812.0001C Description Features FeaturesOverview Replacement Items and Accessories ComponentsIncluded Items Bad Boy Luminaire External Components and Controls Major Components and ControlsInstallation Power Power and Data Cabling RequirementsData DMX512 CablesRecommended Cable Types XLR 5-pin connectors should be wired as followsEthernet Cables DMX512 Male Termination ConnectorInstallation Procedures Unpacking and Attaching Hanging BracketsTo unpack and attach brackets Standard Hang To install in standard 2-point hangStandard Hanging Configuration and Dimensions Vertical Yoke Out Hang To install in vertical hangVertical Yoke Out Hanging Configuration Standing Position To install in a standing positionData Connections Connecting Power and Data10 Connecting Power and Data Cables To connect power and dataPower Up and Basic Setup Procedures Powering Up the LuminaireTo power up Bypassing Calibration Comm LED OperationTo bypass calibration Setting a Starting Address DMX CommTo program a starting address 15 Selecting a Universe Ethernet Control Ethernet Art-Net CommLamp Operation Settings To start lamp using Menu TouchscreenStarting the Lamp Lamp Warm-UpConfiguring Comm Loss Setting Configuring Universe, Comm, and Other OptionsTo configure the Comm Loss setting Accessory Options To install follow spot handlesFollow Spot Operation Enabling Pan/Tilt Free Mode Using Control ChannelsAt Pan/Tilt Menu Operation Screen Saver Mode Using the Menu TouchscreenMenu System NavigationBattery Wake Switch On-Board BatteryMenu System Overview Menu System OverviewHome Screen Menu DetailsLamp Screen Configuration ScreenInformation Screen Pan/Tilt ScreenStatus Screen Communication ScreenTest Screen DMX512 Operation Channel MappingDMX512 Channel Mapping Wheel Control Wheel ControlGobo Wheel Color WheelsControl Channel Control Channels Control ChannelsChannel Functions Timing ChannelsTiming Channel Mapping Channel Function / Timing Channel RelationshipTiming Channels Timing Channels Timing Channels Zoom Tables Gobo Set Zero PositionTo set zero position Troubleshooting Maintenance Troubleshooting Guide TroubleshootingErrors Mechanism Errors Other Errors Test Screen TestingMechanical Test To perform a group test Group TestSoftware Update Using LumLoader Application Software UpdateDownload the Software Software Crossload Proper Lamp Servicing and Operation Equipment HandlingRemoving the Head Covers Routine MaintenanceParts Tools and Supplies02.9812.0001C To remove Aft Cover Removing the Aft CoverTo remove Upper Enclosure Covers Removing the Enclosure CoversTo clean head filters Cleaning the Head Electrostatic FiltersCleaning the Enclosure Intake Filters To clean enclosure intake filtersTools and Supplies Parts To clean luminaire Cleaning the Luminaire ExteriorTo clean lenses Cleaning the LensesRemoving Front Glass Accessing Zoom Lens Assembly To clean gobo, color and dimmer wheels Cleaning Gobo, Color and Dimmer WheelsTo replace lamp Replacing the LampReplacing the Lamp To adjust lamp Adjusting the LampTo replace a gobo Replacing a Gobo11 Replacing a Gobo 12 Gobo Positions and Alignment To replace a designer color filter Replacing a Designer Color FilterOpen 02.9812.0001C Technical Specifications Control Bad Boy Spot LuminaireTechnical Specifications Bad Boy Road Case Photometric Data AC Line Current / Power vs. VoltageIris Full Open 8º Full Angle 40,000 beam Lumens Narrow ZoomIris Full Open 34º Full Angle 48,000 beam Lumens Medium ZoomIris Full Open 56º Full Angle 50,000 beam Lumens Wide ZoomLogarithmic Beam Illuminance Comparison 8º, 34º and 56º Zoom settings02.9812.0001C Glossary Glossary of Terms Signal Movement of the luminaire around the axis of the tilt tube

02.9812.0001C specifications

Bad Boy Mowers has established itself as a premier manufacturer of innovative lawn care solutions, and the Bad Boy Mowers 02.9812.0001C model epitomizes their commitment to quality, performance, and user satisfaction. This commercial-grade mower is designed for those who take landscaping seriously, combining robust construction with advanced technologies.

One of the standout features of the 02.9812.0001C is its powerful engine, which typically boasts impressive horsepower, allowing it to tackle tough mowing tasks with ease. This model is engineered for longevity and reliability, ensuring that it can handle the demanding needs of professional landscapers as well as homeowners who want the very best for their lawns.

The 02.9812.0001C is designed with a wide cutting deck, often measuring 60 inches, allowing for efficient lawn coverage. This larger cutting width enables users to complete mowing tasks quicker, reducing the amount of time spent on the job. Additionally, the reinforced steel construction of the cutting deck provides durability and resilience, ensuring it can withstand the rigors of frequent use.

One of the key technologies incorporated into this model is its dual hydrostatic transmission system, which offers superior maneuverability and control. This feature allows users to easily navigate around obstacles and tight corners, providing a more precise mowing experience. The intuitive controls enhance the user experience, making it simple for operators of all skill levels to achieve desired results.

Another remarkable aspect of the Bad Boy Mowers 02.9812.0001C is its suspension system, which contributes to a smoother ride, reducing operator fatigue during extended use. This is especially beneficial when mowing uneven terrain, as the suspension effectively absorbs shocks and vibrations.

For enhanced comfort, the mower includes an ergonomic seat designed for maximum support, along with easy-to-reach controls for seamless operation. The model also features a commercial-quality air filtration system, ensuring optimal engine performance while extending maintenance intervals.

In summary, the Bad Boy Mowers 02.9812.0001C is an exceptional choice for those seeking a powerful, efficient, and user-friendly mower. With its advanced features, durable construction, and smart technologies, this model meets the demands of both professional landscapers and dedicated homeowners, making it a worthy investment for anyone serious about lawn care.
Top Page Image Contents