Bad Boy Mowers 02.9812.0001C user manual Replacing the Lamp, To replace lamp

Page 80

BAD BOY™ SPOT LUMINAIRE USER MANUAL

Replacing the Lamp

Parts:

71.2566.1200.0 1 EA LAMP, FASTFIT, PHILIPS MSR GOLD™

Tools and Supplies:

Cotton gloves or finger cots

WARNING: Remove power from luminaire before performing any maintenance procedures.

CAUTION: Refer to "Proper Lamp Servicing and Operation" on page 58 before handling the lamp.

To replace lamp:

Step

1.

Remove power from lamp and allow lamp to cool for at least 5 minutes.

Step

2.

Remove power from luminaire.

Step

3.

At rear of luminaire, rotate backcap counter-clockwise to remove (it will still be connected

 

 

by a tether). Refer to Figure 4-8on next page.

Step

4.

Remove existing lamp by rotating lamp base counter-clockwise and pulling straight out of

 

 

backcap.

Step

5.

Position new lamp as shown in Figure 4-8DETAIL A and insert into rear bulkhead. Rotate

 

 

45 degrees clockwise to lock in place. You will hear a click when properly seated.

Step

6.

Replace backcap.

Step

7.

Reset Lamp Hours. (Refer to "Lamp Screen" on page 34.)

Step

8.

Optimize lamp. (Refer to "Adjusting the Lamp" on page 72.)

70

02.9812.0001C

Image 80
Contents Spot Luminaire Production Resource Group, LLC. All Rights Reserved Safety Notice Compliance Notice02.9812.0001C Iii Revision History This manual has been revised as followsTable of Contents Troubleshooting and Maintenance OperationAppendix B. Glossary Appendix A. Technical SpecificationsRoutine Maintenance Viii Additional Documentation IntroductionAbout This Manual Customer Service PRG Dallas International Service PRG AtlantaGobo Art Submission Guidelines 02.9812.0001C Description Overview FeaturesFeatures Included Items Replacement Items and AccessoriesComponents Major Components and Controls Bad Boy Luminaire External Components and ControlsInstallation Power and Data Cabling Requirements PowerData DMX512 CablesXLR 5-pin connectors should be wired as follows Recommended Cable TypesDMX512 Male Termination Connector Ethernet CablesTo unpack and attach brackets Installation ProceduresUnpacking and Attaching Hanging Brackets To install in standard 2-point hang Standard HangStandard Hanging Configuration and Dimensions To install in vertical hang Vertical Yoke Out HangVertical Yoke Out Hanging Configuration To install in a standing position Standing PositionConnecting Power and Data Data ConnectionsTo connect power and data 10 Connecting Power and Data CablesTo power up Power Up and Basic Setup ProceduresPowering Up the Luminaire To bypass calibration Bypassing CalibrationComm LED Operation To program a starting address Setting a Starting AddressDMX Comm Ethernet Art-Net Comm 15 Selecting a Universe Ethernet ControlTo start lamp using Menu Touchscreen Lamp Operation SettingsStarting the Lamp Lamp Warm-UpTo configure the Comm Loss setting Configuring Comm Loss SettingConfiguring Universe, Comm, and Other Options Follow Spot Operation Accessory OptionsTo install follow spot handles At Pan/Tilt Menu Enabling Pan/Tilt Free ModeUsing Control Channels Operation Using the Menu Touchscreen Screen Saver ModeMenu System NavigationOn-Board Battery Battery Wake SwitchMenu System Overview Menu System OverviewMenu Details Home ScreenConfiguration Screen Lamp ScreenPan/Tilt Screen Information ScreenCommunication Screen Status ScreenTest Screen DMX512 Channel Mapping DMX512 OperationChannel Mapping Wheel Control Wheel ControlGobo Wheel Color WheelsControl Channel Control Channels Control ChannelsTiming Channels Channel FunctionsTiming Channel Mapping Channel Function / Timing Channel RelationshipTiming Channels Timing Channels Timing Channels To set zero position Zoom TablesGobo Set Zero Position Troubleshooting Maintenance Troubleshooting Troubleshooting GuideErrors Mechanism Errors Other Errors Testing Test ScreenMechanical Test Group Test To perform a group testSoftware Update Software Update Using LumLoader ApplicationDownload the Software Software Crossload Equipment Handling Proper Lamp Servicing and OperationRoutine Maintenance Removing the Head CoversParts Tools and Supplies02.9812.0001C Removing the Aft Cover To remove Aft CoverRemoving the Enclosure Covers To remove Upper Enclosure CoversCleaning the Head Electrostatic Filters To clean head filtersTools and Supplies Parts Cleaning the Enclosure Intake FiltersTo clean enclosure intake filters Cleaning the Luminaire Exterior To clean luminaireCleaning the Lenses To clean lensesRemoving Front Glass Accessing Zoom Lens Assembly Cleaning Gobo, Color and Dimmer Wheels To clean gobo, color and dimmer wheelsReplacing the Lamp To replace lampReplacing the Lamp Adjusting the Lamp To adjust lampReplacing a Gobo To replace a gobo11 Replacing a Gobo 12 Gobo Positions and Alignment Replacing a Designer Color Filter To replace a designer color filterOpen 02.9812.0001C Technical Specifications Bad Boy Spot Luminaire ControlTechnical Specifications Bad Boy Road Case AC Line Current / Power vs. Voltage Photometric DataNarrow Zoom Iris Full Open 8º Full Angle 40,000 beam LumensMedium Zoom Iris Full Open 34º Full Angle 48,000 beam LumensWide Zoom Iris Full Open 56º Full Angle 50,000 beam Lumens8º, 34º and 56º Zoom settings Logarithmic Beam Illuminance Comparison02.9812.0001C Glossary Glossary of Terms Signal Movement of the luminaire around the axis of the tilt tube

02.9812.0001C specifications

Bad Boy Mowers has established itself as a premier manufacturer of innovative lawn care solutions, and the Bad Boy Mowers 02.9812.0001C model epitomizes their commitment to quality, performance, and user satisfaction. This commercial-grade mower is designed for those who take landscaping seriously, combining robust construction with advanced technologies.

One of the standout features of the 02.9812.0001C is its powerful engine, which typically boasts impressive horsepower, allowing it to tackle tough mowing tasks with ease. This model is engineered for longevity and reliability, ensuring that it can handle the demanding needs of professional landscapers as well as homeowners who want the very best for their lawns.

The 02.9812.0001C is designed with a wide cutting deck, often measuring 60 inches, allowing for efficient lawn coverage. This larger cutting width enables users to complete mowing tasks quicker, reducing the amount of time spent on the job. Additionally, the reinforced steel construction of the cutting deck provides durability and resilience, ensuring it can withstand the rigors of frequent use.

One of the key technologies incorporated into this model is its dual hydrostatic transmission system, which offers superior maneuverability and control. This feature allows users to easily navigate around obstacles and tight corners, providing a more precise mowing experience. The intuitive controls enhance the user experience, making it simple for operators of all skill levels to achieve desired results.

Another remarkable aspect of the Bad Boy Mowers 02.9812.0001C is its suspension system, which contributes to a smoother ride, reducing operator fatigue during extended use. This is especially beneficial when mowing uneven terrain, as the suspension effectively absorbs shocks and vibrations.

For enhanced comfort, the mower includes an ergonomic seat designed for maximum support, along with easy-to-reach controls for seamless operation. The model also features a commercial-quality air filtration system, ensuring optimal engine performance while extending maintenance intervals.

In summary, the Bad Boy Mowers 02.9812.0001C is an exceptional choice for those seeking a powerful, efficient, and user-friendly mower. With its advanced features, durable construction, and smart technologies, this model meets the demands of both professional landscapers and dedicated homeowners, making it a worthy investment for anyone serious about lawn care.