DeWalt DWE4599N instruction manual Attaching Side Handle Fig

Page 10

IINTENDED USE

This grinder is designed for professional grinding, sanding, wire brushing, polishing or abrasive, cutting-off applications.

DO NOT use under wet conditions or in presence of flammable liquids or gases. This grinder is a professional power tool. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

ANTI-VIBRATION SIDE HANDLE

The anti-vibration side handle reduces vibration and user fatigue in extended use applications.

ANTI-VIBRATION REAR HANDLE (FIG. 1)

The anti-vibration ring (I) reduces handle vibration and user fatigue in extended use applications.

DUST EJECTION SYSTEM

The dust ejection system deflects debris that would be harmful to the motor and allows cleaner air to pass over the motor.

KEYLESS GUARD

This allows for tool-free guard change and adjustment.

E-SWITCH PROTECTION™ (DWE4597N-XE, DWE4599N-XE)

The ON/OFF trigger switch has a no-volt release function. In the event of a power outage or other unexpected shut down, the trigger switch will need to be cycled (turned on and off) to restart tool.

MECHANICAL CLUTCH (DWE4597N-XE, DWE4599N-XE)

The torque limiting clutch reduces the maximum reaction torque transmitted to the operator in the case of jamming a cutting disc. This feature also prevents the gearing and electric motor from stalling. The torque limiting clutch has been factory set and cannot be adjusted.

E-CLUTCH™ (DWE4597N-XE, DWE4599N-XE)

This unit is equipped with an E-Clutch™ (Electronic Clutch), which in the event of a high-load or wheel pinch, the unit will be shut off to reduce the reaction torque to the user. The switch needs to be cycled (turned on and off) to restart tool.

POWER-OFF™ OVERLOAD PROTECTION (DDWE4597N-XE, DWE4599N-XE)

The power supply to the motor will be reduced in case of motor overload. With continued motor overload, the tool will shut off. The switch needs to be cycled (turned on and off) to restart tool. The tool will power off each time the current load reaches the overload current value (motor burn-up point). If continued overload shutdowns occur, apply less force/weight on the tool until the tool will function without the overload engaging.

CONSTANT SPEED UNDER LOAD (DWE4597N-XE, DWE4599N-XE)

The internal electronic speed control offers consistent wheel speed while using the tool.

ELECTRONIC SOFT START (DWE4597N-XE, DWE4599N-XE)

This feature limits the initial start up momentum, allowing the speed to build up gradually over a 1 second period. This feature also reduces the possibility of reduced breaker trips.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or

when making repairs. An accidental start-up can cause injury.

FIG. 2

Attaching Side Handle (Fig. 2)

 

The side handle (G) can be fitted to either side or the top of the

 

gear case in the threaded holes. The side positions are

 

designed for optimized balance in surface finishing and

 

grinding applications. The side handle must be used at all

 

times to maintain proper control of the tool. Before using the

 

tool, check that the handle is tightened securely.

 

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DWE4557-XE, DWE4559-XE, DWE4597N-XE, DWE4599N-XE Page Definitions Safety Guidelines Technical DataElectrical Safety Work Area SafetyPersonal Safety Power Tool USE and Care Electrical SafetyExtension Cords Grinder Safety Warnings Service125 × 6 × Diameter × thickness × bore diameter115 × 6 × 180 × 6 ×Page Safety Warnings Specific for Wire Brushing Operations Safety Warnings Specific for Sanding OperationsSafety Warnings Specific for Polishing Operations Additional Safety Rules for GrindersOr DC Direct current Arsenic and chromium from chemically-treated lumberMinutes Alternating orAttaching Side Handle Fig Switch Fig Wheel Mounting Accessories and AttachmentsRotating the Gear Case Fig Grinding Wheels Sanding Discs Wire Wheels Sanding Flap Discs Cutting Wheels Type 27 guard Hubbed sanding Flap discSurface Grinding with Grinding Wheels FIG Spindle Lock Button FIGMounting NON-HUBBED Wheels To remove the wheel, grasp and turn the backing Surface Finishing with Sanding Flap Discs FIGPlace or appropriately thread backing pad S on the spindle Very Fine FinishingEnvironmental Safety Precautions To Take When Sanding PaintMounting and Using Wire Brushes and Wire Wheels Cleaning and DisposalUsing Wire CUP Brushes and Wire Wheels FIG Mounting and Using Cutting DiscMounting Type 27 or Type 1 Guard Your power tool requires no additional lubrication Cleaning RepairsUsing Cutting Wheels LubricationAccessories Bail Handle
Top Page Image Contents