Craftsman pmn Selecting & Fitting Insert Plate Rings, Selecting the correct size of Ring

Page 12

Router Table for the Craftsman

J.Selecting & Fitting Insert Plate Rings

The Insert Plate Rings are designed to support the workpiece around the cutter to avoid small timber sections tipping or flexing when being machined.

1.First separate all Insert Plate Rings from each other using a sharp knife and trim off all flashes, see fig. J.1.

Selecting the correct size of Ring

2.Select an Insert Plate Ring with an inside diameter approximately 1/4" (6mm) larger than the maximum diameter of the cutter to be used. This will give 1/8" (3mm) gap around the cutter to allow the chips to clear.

3.An Insert Plate Ring is not required for cutters having a diameter of 1 3/4" (45mm) or larger, as the Insert Plate will provide enough support for the workpiece.

4.Do not use router cutters having diameters larger than 50mm (2"). Always ensure the aperture on the base of your router will allow the cutter to protrude through it without touching it.

Fitting Insert Plate Rings

Trim flash

Insert Plate

Ring

here

 

Fig. J.1

The Insert Plate Rings are designed to be snapped into the Insert Plate. Slide the large tab under the edge of the Aperture Hole in the Insert Plate as shown in

fig. J.2.

5.Using you thumb, press down on the Insert Plate Ring until the small tab snaps into position. Ensure the Insert Plate Ring is fully seated into the Aperture Hole.

6.To remove the Insert Plate Ring, release the small tab from the edge of the Aperture Hole and pull the Ring out.

K.Fitting Lead-on Pin

The Lead-on Pin is a safety feature for profiling straight or shaped workpieces with a bearing guided cutter without using a back fence. It will prevent the cutter from snatching the workpiece, especially when using larger cutters or when making heavier cuts. The use of the optional accessory Profiling Top Guard is highly recommended to safely carry out this type of routing operation. See section Y for more information.

Identify the Lead-On Pin, see below.

Lead-on Pin x 1

1.Screw the Lead-on Pin by hand into the Threaded Hole in the Insert Plate, see Fig. K.

2.With a flat screwdriver tighten the pin securely.

3.When you do not require the Lead-on Pin, keep it in a safe place as it is easily misplaced.

Insert plate ring

Fig. J.2

Guide pin

Fig. K

-11-

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Trend R Routing Products from the UK Leader Router Table for the Craftsman Safety Precautions Nuts Dome HeadedTable Leg Assembly of Legs Mounting Table to Workbench or WorkboardMounting Table to a Workmate Fixing Pack Router Models Holes Fixings Identification of Mounting Holes and Screws Re-drilling of Router BaseRe-drilling of Insert Plate Re-drilling both Insert Plate and Router BaseFitting Insert Plate to Table Surface Fitting Router to Insert PlateSelecting & Fitting Insert Plate Rings Selecting the correct size of RingFitting Insert Plate Rings Fitting Lead-on PinClamp Rod x Spring Washer Nut xWing Nut x Clamp Plate x Push Block xAssembly of Tenon Push Block Mounting Push Block Assembly on Back FenceAssembly of Safety Dust Guard to Back Fence Back Fence Components Back Fence xAssembly of Back Fence Attachment of Back Fence to TableMitre Fence Components Assembly of Mitre Fence Alignment of Back Fence to Mitre Fence SlotAssembly of Hose Adaptor Dust Extraction EquipmentAssembly of Spring Pressure Clamps AdjustmentRemove Back Fence from Table Surface Assembly of Profiling Top Guard Adjustment Fit Plate, Washer and Wing NutEdging and Profiling using the Back Fence Release Back Fence Fixing BoltsLock Back Fence Fixing Bolts Using Router Table for Grooving Using Mitre FenceCraft Range Cutter Ref. C116 Using The Profiling Top Guard Producing a ShieldSpecial Notes Moulding the Shield Definition of SnatchingEnd Cutting with the Tenon Push Block Fig. Z.1To socket for plug of router To plug at mains supply Profiling Top GuardFront of CRT Table 59mm Holes for M5 M/C screws 37mm 40mm 54mm 44mm 59.25mm Front Material Approx mm Material MIN .2mm 1/8 Thick

pmn specifications

The Craftsman PMN, or Portable Multi-Tool Navigator, represents a significant evolution in handheld tools, designed to meet the diverse needs of both DIY enthusiasts and professionals alike. This compact device integrates several functionalities, making it an all-in-one solution for a variety of projects, from simple repairs to complex constructions.

One of the standout features of the Craftsman PMN is its ergonomic design. Weighing in at just a few pounds, it offers a comfortable grip, allowing users to handle it for extended periods without experiencing fatigue. The integrated rubberized handle provides extra traction, which increases safety when operating the tool in challenging environments.

Technologically, the Craftsman PMN boasts an innovative power management system. This system cleverly optimizes the energy output based on the selected mode, whether it’s drilling, sanding, or cutting. Coupled with a brushless motor, this technology enhances battery life and reduces noise, allowing for quieter operation without sacrificing performance.

The versatility of the Craftsman PMN is another key characteristic. It features an interchangeable head system that can quickly switch between various attachments. From drill bits and saw blades to sanding discs, users have the flexibility to execute numerous tasks efficiently. The quick-release mechanism simplifies changing attachments, making the transition seamless even in the midst of a project.

Moreover, the Craftsman PMN comes equipped with a built-in LED work light. This feature illuminates dark or hard-to-reach areas, making it an ideal tool for work in poorly lit spaces, such as attics, basements, or outdoors after sunset. Users can enjoy increased visibility, which contributes to precision and safety during operations.

In terms of durability, the Craftsman PMN is constructed with high-quality materials designed to withstand the rigors of professional use. Resistant to dust and moisture, this tool can perform reliably across various environmental conditions, making it a robust option for construction sites or home improvement tasks.

Ultimately, the Craftsman PMN embodies the evolution of multi-tool technology, offering an array of features that cater to the modern user's demands. Combining ergonomic design, advanced technology, versatility, effective lighting, and robust construction, it has established itself as a go-to investment for anyone looking to enhance their toolkit.
Top Page Image Contents