Cisco Systems 520 Mounting the Router in a Rack, Guidelines for Mounting the Router on a Wall

Page 33

Chapter 3 Router Mounting Procedures

Mounting the Router in a Rack

Warning This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 248

Guidelines for Mounting the Router on a Wall

•When choosing a location for mounting the router on a wall, consider cable limitations and wall structure.

•Mount the router with the front panel facing upward. Make sure to mount the router low enough so that you can see the LEDs.

•Make sure that the power supply rests on a horizontal surface such as the floor or a table. If the power supply is not supported, the strain on the power adapter cable could cause it to disconnect from the router.

•Do not install the router or its power supply next to a heat source of any kind, including heating vents.

You can mount the router on a hollow wall or a wall stud. To mount the router, follow these steps:

Step 1 If you have a wireless router, connect the radio antenna to the router (see the “Connecting a Radio Antenna to a Wireless Router” section on page 3-1).

Step 2 Position the router on the wall to determine where to attach the two mounting screws. Make sure the distance between the screws is 8.25 in. (see Figure 3-1 on page 3-2).

Step 3 Mount the router on a wall stud or a hollow wall. Perform one of the following, as appropriate:

•To mount the router on a wall stud, attach two #10 wood screws (round or pan-head) with #10 washers, or two #10 washer-head screws to the wall. Make sure that the screws are long enough to penetrate at least 3/4 in. (20 mm) into the supporting wood or into a metal wall stud.

•To mount the router on a hollow wall, attach two wall anchors with washers to the wall. Make sure that the wall is at least 1/2 in. (12.7 mm) thick and that the wall anchors and washers are a size suitable for the wall to which they are attached.

Step 4 Insert the wood screws or wall anchors (whichever you used) into the mounting-screw holes on the router. Mount the router vertically, with the front panel facing upward and the connection to the power cord facing downward.

Mounting the Router in a Rack

The Cisco Secure Router 520 Series routers can be front-mounted in 19-inch racks only. The mounting brackets are not included with the router. If you choose to mount the router into a rack, you must order the mounting brackets separately.

Cisco Secure Router 520 Series Hardware Installation Guide

 

OL-12892-01

3-3

 

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Americas Headquarters Cisco Secure Router 520 Series Hardware Installation GuidePage N T E N T S Specifications D E OL-12892-01 Objective AudienceOrganization Conventions TroubleshootingAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Xii Related Documentation Obtaining Documentation and Submitting a Service Request Cisco Secure Router 520 Ethernet-to-Ethernet Routers Router ModelsProduct Overview Router Models Cisco Secure Router 520 Series Router-Back Panel Cisco Secure Router 520 ADSL-over-POTS RoutersCisco Secure Router 520 ADSL-over-ISDN Routers Hardware Features LED Indicators on the Routers Serial Number Label LocationColor Description Router Wlan Integrated 802.11b/g Radio Module-Wireless Routers OnlyFeature Description Feature SummaryRouter Memory Router Hardware SecurityRegulatory Compliance OL-12892--01 Safety Warnings and Guidelines Preinstallation InformationStatement 245B Additional Warnings for Wireless RoutersGeneral Safety Guidelines for Wireless Routers Preventing Damage to the RouterPreventing Electrostatic Discharge Damage Unpacking the Box What to Do Next Preparing for InstallationOL-12892--01 Placing the Router on a Desktop Connecting a Radio Antenna to a Wireless RouterFront panel facing upward Mounting-screw holes Mounting the Router on a WallGuidelines for Mounting the Router on a Wall Mounting the Router in a Rack231447 Router Mounting Procedures What to Do Next OL-12892-01 Typical Installation Router InstallationInternet Installing the Cisco Secure Router 520 ADSL-over-POTS Router Router Installation Typical Installation Installing the Cisco Secure Router 520 ADSL-over-ISDN Router NIC Connecting a Server, PC, or WorkstationConnecting to an Ethernet Switch Connecting an External Ethernet Switch OptionalConnecting to a Broadband Modem Connecting a Broadband ModemConnecting the ADSLoPOTS Port to an Adsl Line Connecting an Adsl Line-ADSLoPOTS PortConnecting an Adsl Line-ADSLoISDN Port Connecting the ADSLoISDN Port to an Adsl Line Connecting the AC Adapter Connecting the AC Adapter Connecting an Asynchronous Modem to the Console Port Connecting a Terminal or PC to the Console Port11 Connecting an Asynchronous Modem to the Console Port LEDs to Check Normal Patterns Verifying Router OperationType of Information Before You Call Your Cisco ResellerSymptom Problem Solutions Problems During First StartupSpecifications Problems After the Router Is RunningSymptom Problem Solutions Router Specifications Description Design SpecificationRouter Power LAN Port Pinouts Integrated 802.11b/g Radio ModulePin Function Adsl Port Connector Pinouts Console Connector PinoutsRJ-45 Pin Function DB-9 Pin RJ-11 Pin Function RJ-45 PinEthernet Cable Specifications Cable SpecificationsMaximum Cable Length Type CategoryNumerics IN-2 IN-3 IN-4
Related manuals
Manual 114 pages 29.31 Kb Manual 64 pages 9.13 Kb
Top Page Image Contents