Craftsman 315.275 Light Bulb Replacement, Proper Care of cunERS, Proper Care of Collet

Page 16

LIGHT BULB REPLACEMENT

See Figure 17.

A

c

E

Fig. 17

Unplug your router.

_, WARNING: Failure to unplug your router could result in accidental starting causing

serious injury.

Remove cutter from router. Refer to page 8 to remove cutter.

Adjust router to maximum height.

Remove screws (A) and subbase (B). See Figure 17.

Remove screw (C) and work light lens (D).

With bulb (E) pointing toward you, pull bulb from socket.

Install new bulb by reversing the above procedure.

Reassemble all parts and tighten screws securely.

PROPER CARE OF cu'n'ERS

Get faster more accurate cutting results by keeping cutters clean and sharp. Remove all accumulated pitch and gum from cutters after each use.

When sharpening cutters, sharpen only the inside of the cutting edge. Never grind the outside diameter. Be sure when sharpening the end of a cutter to grind the clearance angle the same as originally ground.

PROPER CARE OF COLLET

From time to time, it also becomes necessary to clean your collet and collet nut. To do so, simply remove collet nut from collet and clean the dust and chips that have collected. Then return collet nut to its original position.

HELPFUL HINTS

,/ Always clamp workpiece securely before routing.

/ A safe operator is one who thinks ahead. ,/ Always wear eye protection when routing.

,/ Make setup adjustments carefully. Then double check. Measure twice and cut once.

,/ Keep cutters clean and properly sharpened.

,/ Don'tlet familiarity make you careless.

,/ Study all safety rules and do the job safely.

J" Never place your hands in jeopardy.

J Make certain clamps can't loosen while in use.

,/ Test difficult setups on scrap-- Don'twaste lumber.

,/ Plan each operation before you begin.

,/ Provide for smoother operation by cleaning your router frequently. Shake router or blow with an air jet to remove sawdust buildup.

/ Think safety by thinking ahead.

16

Image 16
Contents Craftsman Full ONE Year Warranty on Craftsman Router Sears, Roebuck and Co., Dept WA, Hoffman Estates, ILDouble Insulation Symbol Meaning Safety Alert SymbolRead ALL Instructions Rules for Safe Operation Do not USE Tool Under Brownout orBevel Chamfer Bits Panel BIT Straight BitsBIT Round Groove Chamfer Upside Down View of Router Depthindicatorindicator Rings KnowyourrouterINSTALLING/REMOVINGCUTTERS Spindlelock To Lockto Unlock SpindlespindleWRENCHCUI3ER Collet To Loosen Colletnut To TightenDepth of CUT Adjustments Unlock DepthindicatorPoint Depth Adjusting Ring Cutter Inside Subbase Serious injuryBase Depth Indicator Ring Point CUI-rERATZerodepthof CUT Cuiferextended BelowsubbaseRouting Rate of FeedProper Feeding Force FeedingTOO Fast Tooslow TOO Slow FeedingDepth of CUT Depthwidth2ND Pass 2ND Pass RoutingDirection of Feed and Thrust Thrust IllStarting and Ending a CUT Internal Routing Edging with Pilot BitsGuide ROUTER,ORKI Edge RoutingFreehand Routing FREEHANDROUTINGFgRouting with Straight Edge Suebase Routingwithstraightedgeof Subbaseagainstan Edgeguide FigLubrication GeneralExtension Cords Light Bulb Replacement Think safety by thinking aheadProper Care of cunERS Proper Care of ColletPage 36-35 Craftsman Router Model no Parts ListSee Back page for Parts Ordering Instructions M. 5 p.m. CST Men. Sat SU-HOGAR