Special Precautions

IMPORTANT!

Please Read Before Starting

This air conditioning system meets strict safety and operat- ing standards. As the installer or service person, it is an important part of your job to install or service the system so it operates safely and efficiently.

For safe installation and trouble-free operation, you must:

●Carefully read this instruction booklet before beginning.

●Follow each installation or repair step exactly as shown.

●Observe all local, state, and national electrical codes.

●This product is intended for professional use. Permission from the power supplier is required when installing an outdoor unit that is connected to a 16 A distribution network.

●Pay close attention to all warning and caution notices given in this manual.

This symbol refers to a hazard or

WARNING unsafe practice which can result in severe personal injury or death.

This symbol refers to a hazard or

CAUTION unsafe practice which can result in personal injury or product or

property damage.

If Necessary, Get Help

These instructions are all you need for most installation sites and maintenance conditions. If you require help for a special problem, contact our sales/service outlet or your certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for improper installation or maintenance service, including fail- ure to follow the instructions in this document.

WARNING When Wiring

ELECTRICAL SHOCK CAN CAUSE

SEVERE PERSONAL INJURY OR DEATH.

ONLY A QUALIFIED, EXPERIENCED

ELECTRICIAN SHOULD ATTEMPT TO

WIRE THIS SYSTEM.

•Do not supply power to the unit until all wiring and tubing are completed or reconnected and checked.

•Highly dangerous electrical voltages are used in this sys- tem. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inad- equate grounding can cause accidental injury or death.

•Ground the unit following local electrical codes.

•Connect all wiring tightly. Loose wiring may cause over- heating at connection points and a possible fire hazard.

When Transporting

Be careful when picking up and moving the indoor and outdoor units. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin aluminum fins on the air conditioner can cut your fingers.

When Installing…

…In a Room

Properly insulate any tubing run inside a room to prevent “sweating” that can cause dripping and water damage to walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to provide a solid, level foundation for the outdoor unit. This prevents water damage and abnormal vibration.

…In an area with High Winds

Securely anchor the outdoor unit down with bolts and a metal frame. Provide a suitable air baffle.

…In a Snowy Area (for Heat Pump-type Systems)

Install the outdoor unit on a raised platform that is higher than drifting snow. Provide snow vents.

When Connecting Refrigerant Tubing

•Ventilate the room well, in the event that is refrigerant gas leaks during the installation. Be careful not to allow contact of the refrigerant gas with a flame as this will cause the generation of poisonous gas.

•Keep all tubing runs as short as possible.

•Use the flare method for connecting tubing.

•Apply refrigerant lubricant to the matching surfaces of the flare and union tubes before connecting them, then tighten the nut with a torque wrench for a leak-free con- nection.

•Check carefully for leaks before starting the test run.

NOTE

Depending on the system type, liquid and gas lines may

be either narrow or wide. Therefore, to avoid confusion

the refrigerant tubing for your particular model is speci-

fied as either “narrow” or “wide” than as “liquid” or “gas.”

When Servicing

•Turn the power OFF at the main power box (mains) before opening the unit to check or repair electrical parts and wiring.

•Keep your fingers and clothing away from any moving parts.

•Clean up the site after you finish, remembering to check that no metal scraps or bits of wiring have been left inside the unit being serviced.

CAUTION

•Ventilate any enclosed areas when installing or testing the refrigeration system. Escaped refrigerant gas, on contact with fire or heat, can produce dangerously toxic gas.

•Confirm after installation that no refrigerant gas is leak- ing. If the gas comes in contact with a burning stove, gas water heater, electric room heater or other heat source, it can cause the generation of poisonous gas.

SPW-XR254EH56 specifications

The Sanyo SPW-XR254EH56 is a cutting-edge air conditioning unit designed for both residential and commercial applications, offering reliable performance along with advanced features. This model is part of Sanyo’s commitment to providing energy-efficient climate control solutions that ensure comfort while minimizing environmental impact.

One of the standout features of the SPW-XR254EH56 is its high energy efficiency rating. It incorporates advanced inverter technology that allows the system to automatically adjust its cooling and heating output based on the current demand. This ensures that the unit operates at optimal levels, significantly reducing energy consumption and costs. The inverter also helps maintain a consistent temperature within the space, enhancing comfort while preventing the temperature fluctuations commonly associated with traditional units.

In terms of cooling capability, the SPW-XR254EH56 boasts impressive performance metrics. It is designed to efficiently cool medium to large spaces, making it ideal for offices, conference rooms, or larger homes. The unit features a multi-directional airflow system that promotes even distribution of cool air throughout the room, ensuring that every corner is comfortably conditioned.

The Sanyo SPW-XR254EH56 also comes equipped with a range of smart technologies. Its integrated Wi-Fi capability allows users to monitor and control the unit remotely via a smartphone app. This feature enables scheduling, temperature adjustments, and energy usage tracking, offering convenience and enhancing user experience. Additionally, the model includes a programmable timer that further supports energy savings by allowing users to set specific operating times based on their routines.

Noise reduction is another key feature of the SPW-XR254EH56. The unit operates quietly, making it suitable for environments where sound levels need to be kept to a minimum, such as bedrooms or quiet office spaces.

Moreover, the SPW-XR254EH56 is designed with a sleek, modern aesthetic that can seamlessly blend into various interiors. Its durable and compact design not only enhances visual appeal but also ensures reliability and longevity.

In summary, the Sanyo SPW-XR254EH56 stands out for its energy efficiency, advanced inverter technology, smart capabilities, quiet operation, and sleek design, making it an excellent choice for those seeking a dependable and modern air conditioning solution.