Jet Tools Drum Sander operating instructions

Page 4

1.Read and understand this entire manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This sander is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a sander, do not use until proper training and knowledge have been obtained.

5.Do not use this sander for other than its intended use. If used for other purposes, WMH Tool Group disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this sander. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this sander, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power supply.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16.Make sure the sander is firmly secured to the stand or work table before use.

17.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

18.Provide for adequate space surrounding work area and non-glare, overhead lighting.

19.Keep the floor around the machine clean and free of scrap material, oil and grease.

20.Keep visitors a safe distance from the work area. Keep children away.

4

Image 4
Contents Drum Sander Warranty and Service Table of Contents Page Page Introduction Specifications Features and Terminology Contents of the Shipping Container UnpackingAssembling the Open Stand Optional Accessory Casters Optional AccessoryAssembly Installing Drum HeadInstalling Conveyor Table Infeed and Outfeed Tables OptionalDust Cover Installing AbrasivesDust Collection Page Grounding Instructions Adjustments Switch LockoutExtension Cords Drum Height ControlConveyor Belt Tension and Tracking Conveyor Belt ReplacementTrackers Checking Drum Alignment Fine Tuning Drum Alignment Tension Roller Pressure Adjustment Tension Roller AlignmentDrum Height Control Adjustment Basic Operating ProcedureSetting Depth of Cut OperationSelecting SandSmart Feed Rates Tips for Maximum PerformanceMaintenance Edge SandingTracker Kit Underside of conveyor shownAbrasives Abrasive Selection GuideTroubleshooting Motor and Electrical Problems Trouble Troubleshooting Operational Problems Optional Accessories Replacement PartsConveyor and Motor Assembly Parts List Conveyor and Motor Assembly Index No. Part No Description Size QtyDrum Head Assembly Parts List Drum Head Assembly 11-1000-04 Lock Washer, Internal Tooth 12-2000-04 Parts List Open Stand #609004 Optional Accessory Index Part Description Size QtyParts List Closed Stand #609005 Optional Accessory PJN-S022244PLUS-501 2244PLUS-502 Electrical Connections