Bosch Power Tools 3727DEVS, 3725DEVS manual Assembly, Operating Instructions

Page 7

Assembly

BACKING PAD INSTALLATION

The random orbit sander is equipped with a backing pad of soft hardness, which is suitable for general service. Harder and softer pads are available for other purposes, and in general are used as follows;

Extra soft pad - Polishing or sanding large or curved surfaces.

Soft pad - All purpose general sanding and polishing.

Hard pad - Heavy sanding on flat surfaces, especially with coarser abrasives.

To change backing pad, hold pad firmly and turn screw counterclockwise with 5mm allen wrench provided. Remove old pad, and place new pad over locating pins on drive spindle. Replace screw and securely tighten in a clockwise direction with the allen wrench. Damaged or worn backing pads must be replaced immediately (Fig. 1).

BACKING PAD DAMPER

Your tool is equipped with an integrated backing pad damper ring. This damper reduces the no-load speed, which helps prevent accidental marking of the workpiece surface and provides uniform finishing.

NOTE: If you notice steadily increasing no- load speed, this indicates that the damper ring is worn and needs to be replaced.

INSTALLING ACCESSORIES

The random orbit sander uses hook-and-loop backed accessories, which firmly grip the pad when applied with moderate pressure. To change the accessory, merely peel off the old accessory, remove dust from the pad if necessary, and press the new accessory in place. Be sure to align the sanding disc holes with the holes in the backing pad to allow the dust extraction system to function.

After considerable service the pad surface will become worn, and the pad must be replaced when it no longer offers a firm grip. If you are experiencing premature wearout of the pad facing, decrease the amount of pressure you are applying during operation of the tool.

INSTALLING DUST CANISTER

To attach dust canister, slide canister support in direction of arrow (A) until it stops. Insert mounting clip into the pocket provided on canister. Then slide canister support through mounting clip in direction of arrow (B) and push onto the dust port. To remove, reverse this procedure.

DUST COLLECTION CANISTER

The integral dust extraction system collects sanding dust in canister supplied with your sander. For maximum efficiency, the dust canister should be emptied frequently during operation.

When the canister is removed from the tool an (optional vacuum hose accessory) can be attached to the dust port.

To use this feature, attach vacuum adapter and vacuum hose (optional accessories) to dust port, then connect opposite end of the vacuum hose to a shop vacuum cleaner.

CLEANING AND EMPTYING

THE DUST CANISTER

To empty, lift lid of canister. Knock excess dust out of the micro filter, or remove dust with your fingers or a soft brush.

You may notice that all the dust may not come out of the canister. This will not affect sanding performance but will reduce dust collection efficiency.

NOTE: Do not wash the micro filter with soap and water. Dust may become more firmly lodged in the pores, which will reduce dust collection, and damage the micro filter.

Operating Instructions

TRIGGER "ON-OFF" SWITCH

To turn the tool "ON" squeeze the trigger switch. To turn the tool "OFF", release the trigger switch, which is spring loaded and will return to the "OFF" position automatically.

To increase switch life, do not turn switch on and off while tool is under load.

"LOCK-ON" BUTTON

The "Lock-ON" button, located near the trigger allows for continuous operation at maximum OPM without holding the trigger.

TO LOCK TRIGGER "ON": squeeze trigger, depress button and release trigger.

-7-

Image 7
Contents Importante Work Area Power Tool Safety RulesTool Use and Care Safety Rules for Orbital SandersPage Symbols Random Orbit Sander Functional Description and SpecificationsOperating Instructions AssemblyTool Tips Variable Speed with Dial SettingService MaintenanceAccessories Sécurité des personnes Règles de Sécurité GénéralesAire de travail Sécurité électriqueRéparation Consignes de sécurité de la ponceuse à orbite aléatoireLe plomb provenant des peintures à base de plomb Symboles Ponceuse à orbite aléatoire Description fonctionnelle et spécificationsConsignes de fonctionnement AssemblageVariateur DE Vitesse À Cadran Conseils pratiquesPoignée Avant Entretien MaintenanceNettoyage Accessoires Seguridad personal Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad eléctricaServicio Normas de seguridad para lijadoras de órbita al azarPage De Ni-Cd SímbolosLijadora de órbita al azar Descripción funcional y especificacionesInstrucciones de funcionamiento EnsamblajeMango Delantero Consejos para la herramientaRodamientos MantenimientoLubricacion DE LAS Herramientas Escobillas DE CarbónZapata de soporte dura AccesoriosPage Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 40 pages 19.08 Kb