5 |
7 |
6 |
8 |
Cleaning and Disposal
•All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently.
•Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash
•All toys, washable furniture and utensils used by children should be washed thoroughly before being used again.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in
Operating Instructions
WARNING: To reduce the risk of serious personal injury, read and follow all important safety warnings and instructions prior to using this tool.
Switch
To turn the tool ON, hold it as shown in Figure 1 and push the portion of the switch marked "I". To turn the tool OFF, push the portion of the switch marked "O".
Operation (Figure 1)
Grasp product as shown in figure 1 and turn it on. NOTE: Do not rest fingers on platen during use. Move it in long sweeping strokes across the surface, letting it do the work. Light pressure is all that is required for sanding, polishing or scrubbing. Excessive pressure will slow the tool and produce inferior results. Check your work often, product is capable of removing material rapidly.
WARNING: Shock hazard. Under no circumstances should this product be used near water.
9
Extension Cords
When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
|
|
| Minimum Gage for Cord Sets |
|
| ||
Volts |
|
| Total Length of Cord in Feet |
| |||
120V |
|
| |||||
240V |
|
| |||||
Ampere Rating | American Wire Gage |
|
| ||||
More |
| Not more |
|
| |||
Than |
| Than |
|
|
|
|
|
0 | - | 6 | 18 | 16 | 16 | 14 |
|
6 | - | 10 | 18 | 16 | 14 | 12 |
|
10 | - | 12 | 16 | 16 | 14 | 12 |
|
12 | - | 16 | 14 | 12 | Not Recommended |
| |
|
|
|
|
|
|
|
|
Symbols
The label on your tool may include the following symbols.
V | volts | A | amperes | |||
Hz | hertz | W | watts | |||
min | minutes | no | alternating current | |||
|
| direct current | no load speed | |||
|
| |||||
| .......................... | Class II Construction |
|
| ........................ | earthing terminal |
|
|
|
|
| ||
|
|
|
|
| ||
| ........................ | safety alert symbol | .../min | revolutions or | ||
|
|
|
|
|
| reciprocations per minute |
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
Safety Warnings and Instructions: Sanders
•ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION.
•Clean your tool out periodically.
Other Important Safety Warnings and Instructions
Sanding
Lead Based Paint
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we recommend the following precautions when sanding any paint:
Personal Safety
•No children or pregnant women should enter the work area where the paint sanding is being done until all clean up is completed.
•A dust mask or respirator should be worn by all persons entering the work area. The filter should be replaced daily or whenever the wearer has difficulty breathing.
•NOTE: Only those dust masks suitable for working with lead paint dust and fumes should be used. Ordinary painting masks do not offer this protection. See your local hardware dealer for the proper (NIOSH approved) mask.
•NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work area where dust would settle on them.
Environmental Safety
•Paint should be removed in such a manner as to minimize the amount of dust generated.
•Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness.
•Sanding should be done in a manner to reduce tracking of paint dust outside the work area.
CAUTION: To reduce the risk of injury, turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories.
Detail Sanding
Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces and tight spots or corners.
The pad tips may wear unevenly, depending on use. The pads are designed to allow you to interchange and /or rotate the diamond tip.
Fitting sanding sheets (Fig. 2)
•Detach the two
•Hold the tool with the sanding base facing upwards.
•Place the sanding sheet onto the sanding base.
The
•When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again.
•When the whole tip is worn, remove it from the sanding base and fit a new tip.
Tip of the Sanding Base (Fig. 3)
When the sanding base tip is worn, it can be reversed or replaced.
• Reverse or replace the worn part.
Finger Attachment (Fig. 4)
The finger attachment is used for fine detail sanding.
•Remove the screw.
•Remove the
•Fit the finger attachment onto the sanding base.
•Fit and tighten the screw.
•Align the sanding sheet with the finger attachment.
Contour Holder Attachment (Fig. 5)
•The contour sanding pieces are for sanding curved surfaces and grooves.
•Remove the screw.
•Remove the
•Fit the contour holder onto the sanding base.
•Fit and tighten the screw.
Fitting and Removing a Contour Piece (Fig. 6 & 7)
•Choose the contour sanding piece profile most suitable for your application.
•Place one end of the contour sanding piece into the recess at the front end of the contour holder.
•Push the other end of the contour sanding piece until it clicks into place.
•To remove the contour sanding piece, push it forward then pull the rear end out of the contour holder (fig. 7).
Fitting a Sanding Sheet Onto a Contour Sanding Piece (Fig. 8)
•Align the sanding sheet with the contour sanding piece.
•Press the sanding sheet onto the contour sanding piece, making sure that the sanding sheet follows the shape of the profile.
Dust Extraction (Fig. 9)
To Empty Dust Canister:
•The dust canister should be emptied after every 10 minutes of sanding.
•While holding the sander, grasp the dust collection canister and pull off of the sander.
•Remove the canister door and gently shake or tap the canister and door to empty.
•
CAUTION: Respiratory hazard. Never operate this tool for wood sanding unless the
dust canister is in place. Sanding dust exhaust may create a breathing hazard.
WARNING: Fire hazard. Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can
WARNING: Fire hazard. When working on metal surfaces, do not use the dust canister or a vacuum cleaner because sparks are generated. Wear safety glasses and a dust mask. Due to the danger of fire, do not use your sander to sand magnesium surfaces. Do not use for wet sanding.
TROUBLESHOOTING
Problem | Possible Cause | Possible Solution |
• Unit will not start. | • Cord not plugged in. | • Plug tool into a working outlet. |
| • Circuit fuse is blown. | • Replace circuit fuse. |
|
| (If the product repeatedly |
|
| causes the circuit fuse to |
|
| blow, discontinue use |
|
| immediately and have it |
|
| serviced at a Black & Decker |
|
| service center or authorized |
|
| servicer.) |
| • Circuit breaker is tripped. | • Reset circuit breaker. |
|
| (If the product repeatedly |
|
| causes the circuit breaker to |
|
| trip, discontinue use |
|
| immediately and have it |
|
| serviced at a Black & Decker |
|
| service center or authorized |
|
| servicer.) |
| • Cord or switch is damaged. | • Have cord or switch |
|
| replaced at Black & Decker |
|
| Service Center or Authorized |
|
| Servicer. |
• Dust is not | • Sandpaper holes do not align. | • Use Mouse® sandpaper |
being collected. |
| with the appropriate hole |
|
| configuration. |
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at